Irradiation is the main component for producing the electricity from solar energy. When obstacles come in between the sun and the PV cell then it doesn't get sufficient irradiance to produce enough electricity. Shadowing has a great impact on photovoltaic cell. The main fuel of PV cell is solar radiation. Using solar radiation, a photovoltaic cell produces electricity. The shadow on a PV cell decreases the output of the photovoltaic cell. It has been already shown in different papers that shadow effect decreases the output of the PV cell. There are different kinds of shadow effects which are observed, some minimize the PV cell output and some reduce the output to zero. There are different types of shadow based on their effects on the photovoltaic cell. The shadow has also effects depending on whether the PV cells are connected in series connection or in parallel connection. In series when one cell is out of order then the whole series of the PV cells will not work but in parallel connection if one cell is damaged, the others will work because they work independently. According to the output requirement the arrangement of the PV cells are made in series or parallel. Simulink modeling is made for series and parallel connection between two PV cells and the shadow effect is analyzed on one of the PV cells. Using SIMULINK, the shadowing is simulated on the two PV cells, where in one system they are in series and in another system they are in parallel. Slowly the irradiance is decreased to simulate the shadow effect. Simulation of the shadow effect gives an idea about the output of the PV cell system when system has shadow on the PV cells. Here the shadow effect on the two PV cells using series and parallel combinations are simulated and analyzed for understanding the effects on output.

Shockley diode equation is basic for single diode model equation, which is overly used for characterizing the photovoltaic cell output and behavior. In the standard equation, it includes series resistance (R_s) and shunt resistance (R_sh) with different types of parameters. Maximum simulation and modeling work done previously, related to single diode photovoltaic cell used this equation. However, there is another form of the standard equation which has not included Series Resistance (R_s) and Shunt Resistance (R_sh) yet, as the Shunt Resistance is much bigger than the load resistance and the load resistance is much bigger than the Series Resistance. For this phenomena, very small power loss occurs within a photovoltaic cell. This research focuses on the comparison of two forms of basic Shockley diode equation. This analysis describes a deep understanding of the photovoltaic cell, as well as gives understanding about Series Resistance (R_s) and Shunt Resistance (R_sh) behavior in the Photovoltaic cell. For making estimation of a real time photovoltaic system, faster calculation is needed. The equation without Series Resistance and Shunt Resistance is appropriate for the real time environment. Error function for both Series resistance (R_s) and Shunt resistances (R_sh) have been analyzed which shows that the total system is not affected by this two parameters' behavior.

The paper states an introduction, description and implementation of a PV cell under the variation of parameters. Analysis and observation of a different parameters variation of a PV cell are discussed here. To obtain the model for the purpose of analyzing an equivalent circuit with the consisting parameters a photo current source, a series resistor, a shunt resistor and a diode is used. The fundamental equation of PV cell is used to study the model and to analyze and best fit observation data. The model can be used in measuring and understanding the behaviour of photovoltaic cells for certain changes in PV cell parameters. A numerical method is used to analyze the parameters sensitivity of the model to achieve the expected result and to understand the deviation of changes in different parameters situation at various conditions respectively. The ideal parameters are used to study the models behaviour. It is also compared the behaviour of current-voltage and power-voltage by comparing with produced maximum power point though it is a challenge to optimize the output with real time simulation. The whole working process is also discussed and an experimental work is also done to get the closure and insight about the produced model and to decide upon the validity of the discussed model.

Many Radiative Transfer Models (RTM) have been developed to simulate and estimate solar irradiance. Theirs accuracy is well documents in literature nonetheless the effect of the parameters uncertainties on the established models has not been well studied yet. This work focuses on implementing a RTM based on the models found in the literature along with some updates, with the aim to study the sensitivity of the model towards the variations of the input parameters. The parameters studied in this paper are: the day of the year, the solar zenith angle, the local atmospheric pressure, the local temperature, the relative humidity, the height of ozone layer concentration, the ozone concentration, the single scattering albedo, the ground albedo, the Ångström’s exponent and the aerosol optical depth. The sensibility analysis is achieved using the Normalized Root Mean Square Error (NRMSE) as an independent function, calculated with a set of simulated measurements of spectral global solar irradiance and a reference spectrum generated with a group of standard input parameters.

Solar radiation takes in today's world, an increasing importance. Different devices are used to carry out spectral and integrated measurements of solar radiation. Thus the sensors can be divided into the fallow types: Calorimetric, Thermomechanical, Thermoelectric and Photoelectric. The first three categories are based on components converting the radiation to temperature (or heat) and then into electrical quantity. On the other hand, the photoelectric sensors are based on semiconductor or optoelectronic elements that when irradiated change their impedance or generate a measurable electric signal. The response function of the sensor element depends not only on the intensity of the radiation but also on its wavelengths. The radiation sensors most widely used fit in the first categories, but thanks to the reduction in manufacturing costs and to the increased integration of electronic systems, the use of the photoelectric-type sensors became more interesting. In this work we present a study of the behavior of different optoelectronic sensor elements. It is intended to verify the static response of the elements to the incident radiation. We study the optoelectronic elements using mathematical models that best fit their response as a function of wavelength. As an input to the model, the solar radiation values are generated with a radiative transfer model. We present a modeling of the spectral response sensors of other types in order to compare the behavior of optoelectronic elements with other sensors currently in use.The first author gratefully acknowledges the financial support of “Fundação para a Ciência e Tecnologia” (FCT – Portugal), through the Doctoral Grant SFRH/BD/108484/2015. The work is co-funded by the European Union through the European Regional Development Fund, included in the COMPETE 2020 (Operational Program Competitiveness and Internationalization) through the ICT project (UID / GEO / 04683/2013) with the reference POCI-01-0145-FEDER-432 007690

A photovoltaic cell is a component which converts light energy into electrical energy. Different environmental parameters and internal parameters have a great impact on the output of the photovoltaic cell. To identify its characteristics and estimate the output, the well known Shockley diode equation is used. This equation contains all the parameters, as one environmental and different internal. The properties of these parameters were studied and their sensitivity have been analyzed through the use of an error function; this error function allows the study of the behaviour of the parameters and their characteristics against the output of the photovoltaic cell through the analysis of its curves giving the sensitivity of the different parameters to the output of the photovoltaic cell. Using these results the impact of the parameters of the photovoltaic cell has been clearly identified. White noise is included both with the ideal values and the simulation and the ideal value is imposed to get the real time environment flavor. This work analyses both systems with and without white noise.