Jiong Yang

Dr. Jiong Yang


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 July 2022 in Advances in Mechanical Engineering
Verified
Journal Article
Open access
YXYicun Xu
Yicun Xu
YJYujie Ji
Yujie Ji
JYJiong Yang
Jiong Yang
LCLei Cheng
Lei Cheng
HWHaonan Wang
Haonan Wang
BZBenshun Zhang
Benshun Zhang
In shipbuilding, welds in sub-assemblies and unit-assemblies are long and various type. The robot arm needs the gantry movement to cooperate with the welding operation. However, there are joint redundancy and double-arm coordination problems, which cause difficulties in the welding trajectory planning. This paper proposes a strategy of decoupling the dual-arm system into a single-arm system for separate planning and prioritizing joint motion, and conducts welding trajectory planning research based on Matlab’s Simscape Multibody. Firstly, the 3D model of the welding workstation is established, its structure, the operation mode of the joint link and the degree of freedom are analyzed. The 17-DOF welding workstation is decoupled into a single-arm 9-DOF system, a kinematic model is established, kinematic analysis is carried out. The Matlab robot toolbox is used for simulation verification. Then the discretization of weld types and poses in sub-assemblies and unit-assemblies workpieces is analyzed. Finally, the welding workstation and workpiece model are imported into Simscape Multibody of Matlab to simulate the trajectory planning of different types of welds. The simulation results prove the effectiveness of the strategy and have certain reference significance for on-site welding in shipbuilding.

23 February 2022 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
Verified
Journal Article
Closed access
JYJiong Yang
Jiong Yang
BHBifu Hu
Bifu Hu
YTYuan Tao
Yuan Tao
JLJixing Li
Jixing Li
This paper proposes a method for the geometric design of axial compressor blades. First, a novel approach for creating 2D blade sections is proposed, where each 2D blade section is obtained by imposing the defined thickness distribution along the camber line. The camber line of each 2D blade section is defined by specifying the angle change of each point on the camber line. In order to make this method applicable to a wider range of blade section design, the camber line of each section can be designed in several (usually 2 or 3) segments. It takes into account the change rule of blade section along the flow channel, which is the most concerned in the aerodynamic design, rather than the specific curve form of blade section. Then, the 2D blade sections are mapped to the corresponding arbitrary rotational flow surface. Finally, the 3D blade model is generated by lofting the blade sections in the flow surfaces. Some typical examples are presented. It shows that this method has good applicability and flexibility to realize the geometric design of multiple types of blades.

23 September 2022 in Measurement and Control
Verified
Journal Article
Open access
HSHongwei Sun
Hongwei Sun
HWHaonan Wang
Haonan Wang
YXYicun Xu
Yicun Xu
JYJiong Yang
Jiong Yang
YJYujie Ji
Yujie Ji
BZBenshun Zhang
Benshun Zhang
In this paper, aiming at the problem of high-precision trajectory tracking of the gantry welding robot system under the influence of uncertain factors, a composite adaptive fuzzy compensation controller based on the computed torque control strategy has been proposed. The controller is composed of an adaptive fuzzy feedback control strategy and a dead zone adaptive fuzzy control strategy, which realizes high-precision trajectory tracking of the gantry welding robot, improves the solving speed of the control algorithm, and its tracking errors has been reduced. Screw theory and Lie group lie algebra are used to solve the problem of high algorithm complexity of controllers in multi-degree-of-freedom robot systems due to Newton-Euler dynamics modeling. Based on the computed torque control, the adaptive fuzzy feedback control strategy is adopted to compensate for the modeling errors and external disturbances in the gantry welding robot system, and the dead zone adaptive fuzzy control strategy is designed to compensate for the nonlinear dead zone structure with unknown parameters. The Lyapunov equation is introduced to prove the stability of the controller. Finally, the controller designed in this paper is compared with the conventional controller through simulation and experiment on the gantry welding robot platform, which verifies the effectiveness and superiority of the controller.

23 July 2022 in Measurement and Control
Verified
Journal Article
Open access
YXYicun Xu
Yicun Xu
LCLei Cheng
Lei Cheng
JYJiong Yang
Jiong Yang
YJYujie Ji
Yujie Ji
HWHaonan Wang
Haonan Wang
BZBenshun Zhang
Benshun Zhang
Aiming at the problem that the traditional inverse solution optimization method is not comprehensive and does not consider the robot structure and actual working conditions, an inverse solution multi-objective optimization method is proposed. This method comprehensively considers the structural size and working state of the welding robot, establishes the stiffness performance evaluation index, optimizes the performance index of the subsequent connecting rod movement area caused by joint rotation, and selects the optimal inverse solution combined with the principle of “minimum joint displacement.” Compared with the traditional method, this method is more comprehensive. It makes the variation range of the rear three small joints of the welding robot larger than the front three large joints, which reduces the power consumption. In addition, it also improves the stiffness of the welding robot at the trajectory point, which ensures the reliability of the welding robot. On this basis, for linear and arc welds, the position interpolation of cartesian space line and arc trajectory based on the S-shaped acceleration and deceleration curve and the posture interpolation of spherical linear interpolation based on unit quaternion are realized. MATLAB simulation results show that the combination of the inverse optimization method and the interpolation method makes the end trajectory, velocity, acceleration, posture curve, and joint displacement curve of the welding robot continuous, smooth, and without mutation.

17 September 2021 in The Visual Computer
Verified
Journal Article
Closed access
PDF file
JYJiong Yang
Jiong Yang
TNTao Ning
Tao Ning
YSYunChao Shen
YunChao Shen