A Spiro fluorene-based dopant-free hole-transporting material denoted as Spiro-IA has been designed and developed from inexpensive starting materials with high yield via a simple synthetic approach for application in perovskite solar cells (PSCs). The unit cost of Spiro-IA can be as low as 1/9th that of the conventional Spiro-OMeTAD. Moreover, Spiro-IA shows good solubility in different organic solvents, e.g. CHCl3, acetone, EtOH, and DMF, and showed favorable charge-transport ability and greater photocurrent density compared to Spiro-OMeTAD. The UV absorption/emission spectra of Spiro-IA (λmax = 430 nm, Emax = 601 nm) are red shifted compared to those of Spiro-OMeTAD (λmax = 388 nm, Emax = 414 nm) with larger stokes shift values (171 nm) which helps suppress the loss of incident photons absorbed by the HTM and is more beneficial for improving the performance of PSCs. Optical and electrochemical studies show that Spiro-IA fulfilled the basic requirements of the hole transfer and electron regeneration process in the fabricated devices. PSCs fabricated (surface area = 1.02 cm2) with dopant-free Spiro-IA achieved a maximum power conversion efficiency (PCE) of 15.66% (JSC = 22.14 mA cm−2, VOC = 1.042 V, FF = 0.679%), which was comparable to that of the most commonly used Li-doped Spiro-OMeTAD (PCE = 15.93%, JSC = 20.37 mA cm−2, VOC = 1.057 V, FF = 0.74%) and surpassed that of the dopant-free Spiro-OMeTAD (PCE = 9.34%). Additionally, the PSCs based on dopant-free Spiro-IA achieved outstanding long-term stability and favorable conductivity (σ = 2.104 × 10−4 S cm−1) compared to those based on Spiro-OMeTAD (σ = 9.00 × 10−8 S cm−1). DFT studies were performed using Gaussian 09 at the B3LYP/6-31G (d/p) level to investigate their electron cloud delocalization in HOMO/LUMO levels. These results showed that Spiro-IA could be a promising candidate for low-cost PSC technology and has a great chance to supersede the expensive Spiro-OMeTAD.
10 September 2020 in Physical Chemistry Chemical Physics
Herein, we report the design and synthesis of four new thiophene-bridged D–π–A configured organic dyes T1–4 comprising different donors, π-spacers and anchoring units, as potential sensitizers and co-sensitizers for DSSCs. The current work also highlights their structural, photophysical, thermal, electrochemical, theoretical, and photoelectrochemical studies, including evaluation of their structure–property relationships. The optical results revealed that the dyes T1–4 display λabs and λemi in the range of 402–461 nm and 556–575 nm, respectively, with a bandgap in the order of 2.31–2.58 eV. Furthermore, the results showed that the dyes possess all the pre-requisites to act as sensitizers/co-sensitizers. Among the tested dyes, the device based on sensitizer T2 achieved the highest PCE compared to the other three dyes, under the standard conditions. Furthermore, their co-sensitized devices were fabricated by co-adsorbing them with the well-known Ru-based MH-12 sensitizer and interestingly the co-sensitizer T3 carrying an alkoxy group and a barbituric acid anchor displayed the highest PCE of 8.79%, which is much higher than that of MH-12 alone (8.18%). Conclusively, the study furnishes a deeper understanding of the intricacies involved in the structural modification of sensitizers/co-sensitizers in achieving an enhanced performance of the devices.
Herein, we report the design, synthesis and characterization of a new series of simple donor–π spacer–acceptor/anchor (D–π–A) type diphenylamine based metal-free organic dyes possessing three different anchoring groups, viz. 4-aminobenzoic acid (DTP), 2-(4-nitrophenyl)acetonitrile (DTN), and barbituric acid (DTB), connected with 2-(thiophene-2-yl)-acetonitrile, as effective sensitizers and co-sensitizers in Dye Sensitized Solar Cells (DSSCs). They were subjected to photophysical, electrochemical and theoretical studies. The dyes exhibited characteristic λabs and λemi in the range of 445–485 and 545–570 nm, respectively. Both optical and electrochemical band gaps were found to be in the range of 2.2 to 2.35 eV. The driving forces for injection (ΔGinj), recombination (ΔGrec) and regeneration (ΔGreg) processes were evaluated to understand their feasibility. Finally, the DSSC devices were fabricated employing the new dyes as sensitizers as well as co-sensitizers along with the Ru(II) based N3 dye. Interestingly, DTP carrying 4-aminobenzoic acid as the anchoring group shows the best photoelectrochemical performance, viz. photovoltaic conversion efficiency (PCE) = 4.4%, open circuit potential (VOC) = 0.577 V, and short-circuit current density (JSC) = 9.06 mA cm−2 with a broad incident photon conversion efficiency (IPCE) spectrum. Co-sensitization of the dyes brought about enhanced VOC values, compared to the N3 dye alone. Finally, different interface resistance values obtained from the electrochemical impedance spectroscopy (EIS) circuit fitting were used to study the fundamental processes of energy conversion.