Harvesting large quantities of timber requires the use of various technical means, including harvesters. The introduction of machine logging has greatly improved safety and reduced accident rates but has also resulted in the risk of musculoskeletal disorders and increased psychological strain. The aim of this study was to determine the level of the mental workload of harvester operators in wind-damaged stands, during daytime and nighttime clearfelling, and during late thinning using the technique of eye-tracking (analysis of saccades and pupil dilation). The highest number of saccades for both felling and processing operations was recorded during daytime and nighttime clearcutting, while the lowest number was recorded in late thinning. For both operations, the highest mean saccade duration was found in late thinning (felling 38.7 ms, processing 36.0 ms) and the lowest in nighttime cutting (felling 33.1 ms, processing 35.5 ms). The highest frequency of saccades in both operations was recorded in clearcut areas during both daytime and nighttime operations. The largest mean pupil diameters during saccades were recorded in night clearfelling plots (felling 5.57 mm, processing 5.52 mm), while the smallest were recorded in plots with windbreaks (felling 2.91 mm, processing 2.89 mm). Comparison of the number, duration, frequency, and time proportion of saccades as well as pupil diameter provided a quantifiable assessment of mental workload in clearcut, wind-damaged, and thinning stands. The indicators analyzed showed that the cutting category can significantly affect the level of mental workload and thus fatigue of harvester operators.

A brush cutter is the most frequently used equipment for tending young forests. When cutting unwanted vegetation, the operator is exposed to various harmful factors, such as: a forced body position, noise, vibrations and exhaust emissions. In this study, the impact of cutting attachment type on the noise level during tending of young pine stands was examined. The attachments used during the tests included: a wire head and cutting blades with 2, 3 and 24 cutting teeth. The research was carried out on 2–3 year old Scots pine plantations covered with three types of vegetation: herbaceous, mixed and woody. It was proven that the the wire head was the device that generated the highest level of noise. In the case of cutting blades, the number of cutting teeth was the important factor. The greater the number of teeth in the cutting blades, the lower the noise level the device produced. There was no significant influence of vegetation type on noise emission level. Based on the results, in order to minimize operators’ exposure to noise, the use of wire cutting attachment should be limited.

The aim of this study was to investigate the effect of season of the year on the frequency and degree of damage to residual trees caused during winter and summer timber harvesting operations in young alder stands. Analyses were conducted in pure black alder (Alnus glutinosa Gaertn.) stands aged 38 and 40 years, located in north-eastern Poland. Chainsaw logging was performed in the cut-to-length (CTL) system, while timber was extracted using an agricultural tractor with a trailer with manual timber loading and unloading. Damage caused in the stand as a result of early thinning operations was evaluated in terms of: (1) damage location, (2) wound size, (3) wound depth, and (4) the distance of the damaged tree from the skid trail. Timber harvesting caused damage in 8.3% of trees remaining in the stand. Both the total number of damaged trees (p = 0.001) and the number of trees damaged during felling (p = 0.01) and extraction of timber (p < 0.001) were greater in summer than in winter. Irrespective of the season, two-thirds of all cases of damage were caused during timber extraction, with 67.7% of damage recorded on trunks or root collars and 32.3% on roots. Irrespective of the season and the technological operation, slightly over 50% of cases of damage were small wounds of max. 10 cm². The proportions of medium-sized wounds (11–100 cm²) and large wounds (over 100 cm²) were comparable. The majority of damaged trees (85.1%) were found in the vicinity (<1 m) of the skid trails. The frequency of tree damage near the skid trail was twice as large in summer as in winter (p < 0.001).

Harvested timber requires efficient and accurate measurements for timber trade. Recently, the amount of timber that is harvested for industrial purposes is growing and methods for roundwood measurements are under constant development. Some of these solutions are with certification confirming its accuracy, some of them are proposed for general use without certification. The aim of this paper was to select the best and most useful electronic solution for timber volume masurement and calculation, and to recommend the most effective and accurate solution for future timber trade. Three photo-optical systems were tested: LogStackPro, iFovea and Timbeter. Each system was used to measure 71 stacks of pine and oak roundwood, which amounted to 3481.15 cubic meter stacked. Timber volumes obtained from the manual measurements were used as reference. Volumes obtained from the photo-optical systems were larger in comparison with the volume from manual measurements, by 3.37, 8.07 and 9.08%, in LogStackPro, iFovea and Timbeter, respectively. It was concluded from the tested systems that, currently, the most recommended solution for timber measurement will be LogStack Pro, which also presented, in most cases, the smallest deviations from the volume obtained in manual measurements.

Silver birch ( Roth) is classified in diffuse-porous wood category. In this case structure of wood tissue is quite similar across whole cross-sectional area. The aim of this study was to analyse cross-section variability of moisture content (MC) of growing silver birch wood, significant hardwood species in Polish forests. Investigations were performed on 120 model trees. In the trunk of each model tree, an increment core was collected at breast height. Samples were collected of 30 different trees in four different seasons. The greatest MC was observed during winter, lowest MC in summer. Differences in MC were statistically significant only between winter versus spring, summer, and autumn. Distribution of MC on cross-section was similar in each season. The greatest average value was observed close to pith, then it was decreasing in bark direction. The greatest difference between observed in spring – 19.51% (p < 0.05) and lowest in autumn – 4.66%. Distribution of green density (GD) on cross section was inverse proportional to MC value. Variations in GD and MC are relevant for log transport planning, weight-scaling systems, lumber drying and dynamic assessment of stiffness. Therefore, from an environmental loss perspective, it is important to determine changes in MC and GD across the year.Betula pendula

This experiment was conducted in the pine woods of central Europe at a research area established in 1951. The experimental area of 1.35 ha was set up in a 14-year-old pine tree stand, which was divided into lots, and the pruning procedure took place in different variants. Some lots constituted control lots without pruned trees. The trees were pruned in four variants, reducing the living tree crown by 1/4, 1/3, 1/2, and 2/3 of its length. The study’s main aim was to determine the influence of pruning forest trees on the tree tissue. Moreover, the study attempted to answer whether pruning was a significant procedure for wood valorisation, and if yes, then which variant was the optimal one for Scots pine growing on the European plain. The results indicated a significant impact of pruning young pine tree stands on the properties of wood tissue, which differed regarding the adopted pruning variant. Significant differences in the width of annual rings, the size of the particular areas of the annual rings (latewood or earlywood), and the wood density depending on the pruning variant were observed. Furthermore, the results indicated that pruning induced numerous processes, which optimised the physiological and mechanical functions of the tree trunks. The outcome of this optimisation was, among others, the diversification of the vascular and strengthening area of the annual ring as well as the wood density, which was a reaction to reducing a part of the assimilation apparatus. From the technical wood value viewpoint, the optimal pruning variant for pine was between 1/3 to 1/2 of the living crown.