Amir Farhad Najafi

Dr. Amir Farhad Najafi

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2020 in Renewable Energy
Verified
Journal Article
Closed access
SPS. Abdolkarim Payambarpour
S. Abdolkarim Payambarpour
ANAmir Farhad Najafi
Amir Farhad Najafi
FMFranco Magagnato
Franco Magagnato

1 April 2015 in Journal of Turbomachinery
Verified
Journal Article
Closed access
PDF file
HAHamed Alemi
Hamed Alemi
SNSeyyed Ahmad Nourbakhsh
Seyyed Ahmad Nourbakhsh
MRMehrdad Raisee
Mehrdad Raisee
ANAmir Farhad Najafi
Amir Farhad Najafi

7 February 2022 in Engineering Applications of Computational Fluid Mechanics
Verified
Journal Article
Open access
MSM. Shadab
M. Shadab
MKM. Karimipour
M. Karimipour
ANAmir Farhad Najafi
Amir Farhad Najafi
RPR. Paydar
R. Paydar
SNS. Ahmad Nourbakhsh
S. Ahmad Nourbakhsh
The effect of pump impeller modification by a new approach, pump impeller shroud trimming (PIST), on the flow field and pump performance is examined both numerically and experimentally. The primary purpose of this study is to investigate the hydraulic performance of single-phase centrifugal pumps, which are refined by the PIST method, with low and medium specific speeds. In this type of shroud trimming, different trimming sizes are applied only to the shroud plate of the closed impeller, while the geometries (diameters) of the hub and blades remain unchanged. This modification, which increases the clearance between the impeller and casing from the shroud side, causes desirable conditions for pumping fluid containing undissolved gas. Computational fluid dynamics software (ANSYS-CFX) is used to predict the hydraulic performance of centrifugal pumps. Two well-known turbulence models, the renormalization group (RNG) k-ϵ developed model and shear stress transport (SST) k-ω, are used to predict the flow patterns. The computational results are verified through the comparison of experimental and unsteady numerical simulations with steady numerical data. After ensuring the accuracy of the flow-field simulation approach, further numerical analysis is performed for both pumps by changing the impeller shroud diameter. The effects of the geometric changes on the performance curves, efficiency, flow field, pressure distribution inside the pump components and the radial force acting on both pump types are investigated comprehensively. The results show that the shroud trimming reduces the produced head and efficiency at the design points. Examination of the radial force, which is applied on the rotating parts, shows that shroud-trimmed impellers experience higher radial forces than closed impellers in both pump types owing to the lack of a uniform pressure distribution around the impeller outlet. Accordingly, the relevant information obtained is used to modify the existing coefficients to predict the radial forces.

22 July 2019 in International Journal of Rotating Machinery
Verified
Journal Article
Open access
PDF file
SPS. Abdolkarim Payambarpour
S. Abdolkarim Payambarpour
ANAmir Farhad Najafi
Amir Farhad Najafi
FMFranco Magagnato
Franco Magagnato
Level of utilization of clean energy has grown dramatically in recent years due to increased pollution and environmental issues. For instance, the extra potential energy in water supply system is usually wasted, due to its low capacity. Design of a proper turbine has recently been given more attention by researchers to apply this clean energy. In the present paper, a modified Savonius turbine, suitable for use in a 4-inch pipe, is designed. Turbine with two blades is tested in a laboratory rig and also simulated with the FLUENT software. By matching numerical and laboratory results, simulations are expanded and the blades number effect on turbine performance is studied under determined hydraulic conditions. The flow field around the modified Savonius turbine is interpreted by the 3D streamlines and pressure contours. The obtained results indicate that increasing the turbine blade numbers up to 5 and more causes the turbine efficiency first to rise and then to fall, respectively.

1 October 2019 in Archive of Applied Mechanics
Verified
Journal Article
Closed access
PDF file
NKNima Khoshkalam
Nima Khoshkalam
ANAmir Farhad Najafi
Amir Farhad Najafi
MRMohammad H. Rahimian
Mohammad H. Rahimian
FMFranco Magagnato
Franco Magagnato

5 June 2019 in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
Verified
Journal Article
Closed access
PDF file
SPS Abdolkarim Payambarpour
S Abdolkarim Payambarpour
ANAmir Farhad Najafi
Amir Farhad Najafi
Due to limitation of energy resources, a large body of research activities has been turned to investigate potential alternative avenues to supply energy. In this regard, the renewable sources, which can provide the sustainable and cleaner energy production, have increasingly become attractive. Hydropower has the highest proportion of the renewable energy sources. Availability and high efficiency are the undeniable advantages of the hydro potentials. In this paper, hydro-energy extraction from pipelines by a new designed vertical axis turbine is studied experimentally and numerically. The turbine scheme is inspired by the Savonius rotor turbine, which includes two semicircular blades that is built by the 3D printer and installed vertically in a 100 mm transparent pipe. A sloped block is used just before the turbine blades to concentrate the flow and enhance the efficiency. In experiments, flow rate ranges from 2.7 × 10−3 m3/s to 7.3 × 10−3 m3/s and pressure drop that occurs through the turbine is less than 10.5 kPa. Numerical results show an acceptable agreement with experiments and assure that numerical method is reliable. Following successful validation, numerical studies are expanded, in order to study more details on the new turbine performance. According to the numerical results, the characteristic curves of the new turbine are depicted and described. In numerical simulation, for different turbine rotational speeds, the flow rate and the pressure difference examined are up to 12 × 10−3 m3/s and 30 kPa, respectively. Using the obtained results, investigations and studies are performed to describe turbine behavior under the effects of changing the clearance and flow field conditions. Finally, cyclic variations of turbine flow rate, torque and minimum pressure on the turbine blade are described by velocities streamlines. This approach might preform design improving for such a turbine.