Bingwen Zhou

Bingwen Zhou

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
BYBin Ya
Bin Ya
YXYang Xu
Yang Xu
LMLinggang Meng
Linggang Meng
BZBingwen Zhou
Bingwen Zhou
JZJunfei Zhao
Junfei Zhao
XZXingguo Zhang
Xingguo Zhang
An innovational self-reduction molecular-level-mixing method was proposed as a simplified manufacturing technique for the production of carbon nanotube copper matrix composites (CNT/Cu). Copper matrix composites reinforced with varying amounts of (0.1, 0.3, 0.5 and 0.7 wt%) carbon nanotubes were fabricated by using this method combined with hot-pressing sintering technology. The surface structure and elemental distribution during the preparation of CNT/Cu mixing powder were investigated. The microstructure and comprehensive properties of the CNT/Cu composites were examined by metallography, mechanical and electrical conductivity tests. The results revealed that the CNT/Cu could be produced by a high temperature reaction at 900 degrees under vacuum, during which the carbon atoms in the carbon nanotubes reduced the divalent copper on the surface to zero-valent copper monomers. The decrease in the ratio of D and G peaks on the Raman spectra indicated that the defective spots on the carbon nanotubes were wrapped and covered by the copper atoms after a self-reduction reaction. The prepared CNT/Cu powders were uniformly embedded in the grain boundaries of the copper matrix materials and effectively hindered the tensile fracture. The overall characteristics of the CNT/Cu composites steadily increased with increasing CNT until the maximum at 0.7 wt%. The performance was achieved with a hardness of 86.1 HV, an electrical conductivity of 81.8% IACS, and tensile strength of 227.5 MPa.

31 March 2022 in Materials
Verified
Journal Article
Open access
PDF file
BZBingwen Zhou
Bingwen Zhou
MLMengnan Lv
Mengnan Lv
JWJiali Wu
Jiali Wu
BYBin Ya
Bin Ya
LMLinggang Meng
Linggang Meng
XZXingguo Zhang
Xingguo Zhang
In order to decrease and control electromagnetic pollution, absorbing materials with better electromagnetic wave absorption properties should be developed. In this paper, a nanocrystalline alloy ribbon with the composition of Fe73.2Si16.2B6.6Nb3Cu1 was designed and prepared. Nanocrystalline alloy powder was obtained by high-energy ball milling treatment. The effects of ball milling time on the soft magnetic properties, microstructure, morphology, and electromagnetic wave absorption properties of alloy powder were investigated. The results showed that, as time increased, α-(Fe, Si) gradually transformed into the amorphous phase, and the maximum saturation magnetization (Ms) reached 135.25 emu/g. The nanocrystalline alloy powder was flakelike, and the minimum average particle size of the powder reached 6.87 μm. The alloy powder obtained by ball milling for 12 h had the best electromagnetic absorption performance, and the minimum reflection loss RLmin at the frequency of 6.52 GHz reached −46.15 dB (matched thickness was 3.5 mm). As time increased, the best matched frequency moved to the high-frequency direction, and the best matched thickness decreased, while the maximum effective absorption bandwidth ΔfRL<−10 dB was 7.22 GHz (10.78–18 GHz).

6 April 2023 in Journal of Magnetism and Magnetic Materials
Verified
Journal Article
Closed access
MLMengnan Lv
Mengnan Lv
BZBingwen Zhou
Bingwen Zhou
YLYunfeng Liu
Yunfeng Liu
BYBin Ya
Bin Ya
HJHuimin Jia
Huimin Jia
XZXingguo Zhang
Xingguo Zhang

15 July 2025 in Applied Surface Science
Verified
Journal Article
Closed access
SGShan Gao
Shan Gao
BZBingwen Zhou
Bingwen Zhou
YLYunfeng Liu
Yunfeng Liu
WLWenxing Li
Wenxing Li
YXYixin Xie
Yixin Xie
XZXingguo Zhang
Xingguo Zhang

1 December 2020 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
BZBingwen Zhou
Bingwen Zhou
YYY.G. Yi
Y.G. Yi
HXH. Xu
H. Xu
LML.G. Meng
L.G. Meng
BYB. Ya
B. Ya
XZXingguo Zhang
Xingguo Zhang

5 September 2020 in Materials
Verified
Journal Article
Open access
PDF file
LMLinggang Meng
Linggang Meng
BZBingwen Zhou
Bingwen Zhou
BYBin Ya
Bin Ya
DJDong Jing
Dong Jing
YJYingxi Jiang
Yingxi Jiang
XZXingguo Zhang
Xingguo Zhang
AlMgTi-based metal–intermetallic laminated composites were successfully fabricated through an innovative dual-step vacuum hot pressing. First, this study prepares the AlTi-based laminated composites by vacuum hot pressing at 650 °C. Then, the researchers place the Mg-Al-1Zn (AZ31) magnesium alloy between the prepared AlTi-based laminated composites at 430 °C for hot pressing. This study investigates the microstructure, phase composition, and microhardness distribution across interfaces of the intermetallics and metal. A multilayer phase (Mg17Al12, Al3Mg2, and transition layers) structure can be found from the diffusion layers between Al and AZ31. The microhardness of the material presents a wavy distribution in the direction perpendicular to the layers; the maximum can be up to 600.0 HV0.2 with a minimum of 28.7 HV0.2 The microhardness gradient of an AlMgTi-based composite is smoother due to the different microhardness of the layers, and reduces the interface stress concentration. The bending strength of AlMgTi-based composites can reach 265 MPa, and the specific strength is 105 × 103 Nm/kg, higher than AlTi-based composites.