Many electronic products are subjected to heat for long periods, depending on their operations. Thus, it is expected that the physical and mechanical properties of electronic elements, including the soldering joints, will be affected. In this study, the impact of thermal aging time and temperature on the microstructure and mechanical properties of 96.5Sn–3.0Ag–0.5Cu (SAC305) was investigated. The samples used were SAC305 solder balls attached to copper pads. The research began by examining the microstructure of the aged samples at 150 °C for 100 and 1000 h. Then, this was compared to the microstructure of the same samples without thermal aging. Then, five groups of 10 samples were prepared from a shear stress–shear stain experiment. The first group was as produced, the second group was aged for 2 h, the third group was aged for 10 h, the fourth group was aged for 100 h, and the fifth group was aged for 1000 h. All groups were aged at a temperature of 150 °C. An Instron testing machine was used to plot a shear stress–shear stain curve until the ball was completely sheared off the pad. The mechanical properties, including the ultimate shear strength, the ultimate energy used to shear the ball, and the total energy used to shear the ball at all thermal aging times were then estimated. The results of this study indicated the formation of a layer of Cu6Sn5 over the copper pad, which thickened with thermal aging time. Furthermore, the ultimate and total shear strengths decreased with thermal aging time. The same procedure was repeated to assess the ultimate shear strength at 100 °C. The decrease in ultimate shear strength was more severe with increasing thermal aging temperature.

Solder joints are subjected to varied stress cycle circumstances in the electronic packaging service life but are also influenced by aging. There has been limited investigation into the influence of aging and varying cycles on SnAgCu-Bi (SAC-Bi) solder joint fatigue. Cyclic fatigue tests were performed on solder joints of several alloys, including SnAgCu (SAC305), SnAgCu-Bi (SAC-Q), and SnCu-Bi (SAC-R). Individual solder joints were cycled under varying stress levels, alternating between mild and harsh stress levels. At least seven samples were prepared for each alloy by alternating between 25 mild stress (MS) cycles and three harsh stress (HS) cycles until the solder joint broke off. The impact of aging on Bi-doped solder joints fatigue under varied amplitude stress was examined and predicted for 10 and 1000 h under 125 °C. Because of the “Step-up” phenomenon of inelastic work, a new fatigue model was developed based on the common damage accumulation (CDA) model. The experimental results revealed that aging reduced the fatigue life of the tested solder alloys, particularly that of SAC305. According to the CDA model, all solder alloys failed earlier than expected after aging. The proposed model uses the amplification factor to assess inelastic work amplification after switching between the MS and HS cycles under varying stress amplitude conditions. The amplification factor for the SAC-Bi solder alloys increased linearly with fracture initiation and substantially followed crack propagation until the final failure. Compared with existing damage accumulation models, the proposed fatigue model provides a more accurate estimation of damage accumulation. For each case, the cut-off positions were examined. The SAC-Q amplification factor increased linearly to 83% of its overall life, which was much higher than that of SAC305 and SAC-R. This study identified three distinct failure modes: ductile, brittle, and near intermetallic compound (IMC) failure. It was also observed that SAC-Q with an organic solderability preservatives (OSP) surface finish was more susceptible to brittle failure owing to the excessive brittleness of the alloy material.

During operation, electronic components are exposed to high temperatures that may last for long periods, depending on the operating duration. Solder joints are one of the components most affected by thermal aging while in service. In this research, the effect of thermal aging duration and temperature on the mechanical properties of 92.8%Sn-3%Ag-0.5%Cu-3.3%Bi (Cyclomax) was investigated. The novelty of this work lies in the study of the important properties of a new generation of Sn-Ag-Cu (SAC) materials (i.e., Cyclomax). Cyclomax is rare in industry and immature in research. To understand the effect of thermal aging, the microstructure was investigated, and changes in it and its mechanical properties were observed. To simulate solder joints in electronic devices, samples of solder balls were prepared and attached to copper pads on electronic boards. Most samples were then treated at 150 °C or 100 °C for up to 1000 h and some samples were left untreated for comparison. A scanning electron microscope (SEM) was used to obtain images of the microstructure. The shear stress–shear strain relationships, including the ultimate shear strength (USS), the modulus of elasticity and the ultimate energy (UE), were investigated. The microstructure images indicated the presence of a layer of Cu6Sn5 on top of the copper pad before thermal aging was applied. The thickness of this layer increased with the application of thermal aging over time. The results for the shear stress–shear strain relationship indicate that all of the USS, the total energy (TE) to shear off the solder balls and the UE decreased at the beginning of the thermal aging and then reversed to increase later. In general, isothermal aging reduces the performance of Cyclomax solder joints in terms of the minimum force and energy required to separate and subsequently damage electronic components.

Poly(3,4-ethylenedioxythiophene) (PEDOT) and Indium Tin Oxide (ITO) are widely used in electronic devices, but their stability under thermal stress is a concern. Both PEDOT and ITO are susceptible to thermal stress, but their stability depends on the temperature and duration of exposure. To ensure long-term stability, it is essential to use appropriate thermal management techniques and stable materials. ITO has good mechanical stability under stretching and bending, while PEDOT can withstand high strains. Flexible solar cells are exposed to heating-cooling cycles, and when the thin film and substrate expand at different rates, residual strains caused by the thermal mismatch occur. ITO is heavily used in flexible solar cells, but indium is scarce and expected to run out within 50 years. PEDOT is a candidate to replace ITO and is currently under intensive research. This paper compares the thermal stability of PEDOT and ITO under thermal bending and cycling stress. In order to investigate the significance of different factors on thin film electrical characteristics, the DOE (design of experiments) tool was used for data collection and analysis of variance was used to analyze the data. The results showed that PEDOT is better than ITO under cyclic bending loading, while ITO is slightly more stable than PEDOT under thermal stress. These findings provide new insights into the behavior of PEDOT and ITO under thermal stress and their potential applications in electronic devices.