The synthesis of geometrically tunable nano-size hollow silicate particles (NHSPs) using water-based poly_(methacrylic acid) sodium salt (NaPMA) colloidal nano size-aggregate particles as soft-templates, tetraethyl orthosilicate (TEOS) as a silica precursor and ammonia hydroxide (NH4OH) as a catalyst by simple sol–gel reaction was carried out. Tuning the nano-size diameter of NHSPs between 60 nm and 200 nm and decreasing the shell thickness from 40 nm down to 18 nm were achieved by only varying the concentrations of alternative-NaPMA and the amount of TEOS, respectively. The thermal insulating feature of NHSPs was demonstrated by coating the glass substrate with NHSPs, a reduction of approximately 29.9% in thermal conductivity was observed after coating the glass substrate, which was evaluated by contactless approach using the xenon flash lamp set-up. The coated-glass with NHSPs was prepared by simple sequential adsorption of poly_(allylamine hydroxide) (PAH) followed by deposition of NHSPs on the cleaned glass substrate surfaces using an automated dip coater. The dip coated samples showed good thermal insulating properties as well as good transparency in the visible light range.
In a high-temperature, high-flame-velocity, and high-pressure gas corrosion environment, the intercolumnar pores and gaps of electron beam–physical vapor deposition (EB-PVD) thermal barrier coatings (TBCs) may serve as infiltration channels for molten calcium–magnesium–alumino–silicate (CMAS), leading to the severe degradation of TBCs. In order to clarify the relationship between the roughness of the bond coat and the CMAS corrosion resistance of the EB-PVD TBCs, 7 wt.% yttria-stabilized zirconia (7YSZ) TBCs were prepared on the surfaces of four different roughness-treated bond coats. The effect of the bond coat roughness on the columnar microstructure of the EB-PVD YSZ was investigated. The effect of the change of the bond coat’s microstructure on the CMAS corrosion resistance of the EB-PVD YSZ was studied in detail. The results showed that the reduction in the roughness of the bond coat contributes to the improved formation of the EB-PVD YSZ columns. The small and dense columns are similar to a lotus leaf-like structure, which could reduce the wettability of CMAS and minimize the spread area between the coating and the CMAS melt. Thus, the CMAS corrosion resistance of the coating can be greatly improved. This preparation process also provides a reference for the preparation of other TBC materials, improving the resistance to CMAS hot corrosion.
Diamond-incorporated copper metal matrix layers were fabricated on brass substrates by using electrodeposition technology in this study. To improve the adhesion of the composite coatings on the brass substrate, a plated copper was applied as the interlayer between the multilayers and the substrate. The surface morphologies of the interlayer and the diamond-incorporated copper composite layers were studied by scanning electron microscopy. The effect of the copper interlayer on the incorporation and the distribution of the diamond content in the coatings was analyzed by surface roughness, electrochemical impedance spectroscopy, and cyclic voltammetry. The diamond content of the composite coating was measured by energy-dispersive X-ray. The film thickness was evaluated by the cross-sectional technique of focused ion beam microscopy. The element, composition, and crystallization direction of diamond with Cu matrix was measured by X-ray diffraction and transmission electron microscope. The adhesion of the multilayers was studied by scratch tests. The experiment results indicated that the diamond content and distribution of the coating were higher and more uniform with the Cu interlayer than that without one. The plated copper interlayer reduced the electrical double-layer impedance and enhanced the adsorption of diamond particles by the surrounding Cu ions, which promoted the diamond content in the composite coatings. The roughened surface caused by the plated Cu interlayer also improved the substrate’s mechanical interlock with the composite coating, which contributed to the strong adhesion between them.
To tackle the ever-increasing operating temperature of aero-engines, a La2Ce2O7 (LCO)/yttria partially stabilized zirconia (YSZ) double-layer thermal barrier coating (TBC) was investigated. The LCO/YSZ double-layer samples were annealed with volcanic ash (VA) at 1250 °C to assess their stability in comparison with that of standard single-layer YSZ. The findings showed that the double-layer system exhibited greater resistance to VA damage than the single-layer YSZ coating. The corrosion mechanism was characterized by a rapid crystallization reaction between LCO and VA, where the kinetics of the solution’s reprecipitation reaction outpaced the penetration rate into the coating’s open pores.