The energy paradigm is shifting toward carbon-free and low-emission alternative fuels. Among the many candidates, hydrogen is considered a promising option thanks to its favorable fuel properties, including zero carbon content, high gravimetric energy density, and fast flame speed, despite its technical fuel production and storage challenges. Direct injection technology has been identified as the best approach for applying hydrogen in combustion engines to overcome the accompanying issues, such as backfire and low energy density. However, studies have yet to be conducted on hydrogen jet behavior in direct injection systems, specifically, studies that elucidate engine design and injection parameter optimization in the combustion system. Therefore, we aimed to assess hydrogen jet behavior through experiments and computational approaches comprehensively. Hydrogen was injected at 10 MPa using the direct injection method into a constant volume chamber under a quasi-steady ambient condition. Z-type high-speed Schlieren imaging was performed using a high-speed camera to visualize the hydrogen jet structure, which depicted the hydrogen jet’s vapor intermittency and vortex structure. We also performed a computational fluid dynamics (CFD) simulation to understand the aerodynamics of the jet. The results showed the formation of vortical flow in the inner core region, where the pressure was comparatively lower than that on the outer side of the jet. Our further investigation of the injection strategy showed that multiple injections were more beneficial in forming a favorable hydrogen-air mixture near the spark plug than a single injection case.
The efficiency of light-duty diesel engines should be improved for further emissions regulation. Multi-stage split injection with five injection events was investigated for improvement in efficiency at low-load conditions. The injection timing and quantity were adjusted to achieve a smooth in-cylinder pressure rise and continuous heat release. The multi-stage split injection was compared to injection strategies involving two-pilot and single-main injections. A 0.5 L single-cylinder diesel engine experiment was conducted under low-load conditions. Two multi-stage split injection processes with different combustion phases were developed. The multi-stage split injections yielded a smooth in-cylinder pressure trace and a lower peak heat release rate than the two-pilot injection process. The combustion duration was shorter for multi-stage split injection with an advanced combustion phase, and the fuel consumption was reduced by 1.78% with lower heat transfer, exhaust heat, and combustion loss. The multi-stage split injection flame penetration was shorter than the two-pilot injections. The shorter flame penetration and lower tip velocity reduced the heat transfer to the combustion chamber. The PM emissions were also reduced by 30% under the same NOx emissions, because increased PM oxidation and divided fuel injection prevented flame diffusion and improved air utilization.
Methanol and ethanol are a promising alternative to fossil fuels for the decarbonization of the off-road sectors. Although (m)ethanol are typically seen as fuels for spark ignition engines, mixing-controlled compression ignition (MCCI) combustion is typically preferred in most off-road and medium-and heavy-duty. However, low ignitability presents a major challenge. Blending reactive ignition enhancers, such as 2-ethylhexyl nitrate (EHN), has enabled stable MCCI operation at 1200 rpm & 3.91 bar IMEPn and 1600 rpm & 8.55 bar IMEPn. However, the nitrate group in EHN adversely affects NOx emissions, leading to an 80.9% increase in engine-out NOx compared to non-nitrate enhancers. Conversely, ether-based molecules show significant potential as ignition enhancers due to their high reactivity, and they can be directly produced from renewable sources. To evaluate their effectiveness, experiments and chemical kinetic simulations were performed using ANSYS CHEMKIN-PRO; and results were compared against previous data obtained with EHN. Compared to case with 7% vol EHN, achieving similar ignition characteristics required significantly higher concentrations of ether-based enhancers up to 55% vol DME and 35% vol DEE. This is attributed to the limited effectiveness of the methyl, ethyl, and H radicals produced by ethers in promoting alcohol combustion, compared to the highly reactive OH radicals generated by EHN. Moreover, ethers formed radicals late during the ignition delay time whereas EHN decomposed rapidly, thereby limiting the effect of ethers on (m)ethanol reactivity. Results suggested that it may be more advantageous to introduce ether-based ignition enhancers separately into the cylinder using a dual-fuel (m)ethanol/ether combustion strategy. This approach required only less than 10% energy-equivalent ethers addition to achieve stable ignition, which is even lower than the 11.6% energy-equivalent EHN addition required in the blend-fuel mode. Compression-ignition of port-injected ethers led to high-reactivity in-cylinder conditions to enable ignition of direct-injected (m)ethanol, providing a viable approach for (m)ethanol MCCI combustion.