Rosie Sargent

Ms. Rosie Sargent

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 July 2019 in Journal of Wood Science
Verified
Journal Article
Open access
PDF file
RSRosie Sargent
Rosie Sargent
The degree with which wood shrinks and swells with changing moisture content is an important property which determines its suitability for different applications. This property, known as dimensional stability, is often a target property for improvement in wood modification research. Its importance makes it a commonly quantified wood property. Despite this, methods for measuring dimensional stability are not standardised, and there is little consensus on appropriate test methods. Dimensional stability tests can be classified according to the method used to change the moisture content of the wood (liquid water or water vapour) and the duration of the test (until equilibrium is reached, or a shorter duration). Each class of test represents a situation that wood products may encounter in service, and different types of wood (modified or otherwise) may respond differently to each situation. This means that comparative performance between different wood types may be dependent on the test used (and may not be valid for some situations encountered in service). In this paper, standard test methods and methods described in the literature are compared, and recommendations are given for selecting an appropriate dimensional stability test and for minimising sources of bias and measurement uncertainty in the test. It is expected that this will also encourage the adoption of more standardised test methods, enabling comparisons to be made between different studies and different wood types.

14 April 2022 in Forests
Verified
Journal Article
Open access
PDF file
RSRosie Sargent
Rosie Sargent
Dimensional stability is a commonly targeted property for improvement through wood modification. Here four different tests have been performed on three types of modified wood to compare methods of measuring dimensional stability behavior. These tests cover long and short time periods, as well as dimensional changes caused by contact with liquid water, or from changes in air humidity. All the tests showed increased dimensional stability of the modified samples relative to the unmodified controls; however, the relative behavior of the different modifications varied between tests. Soaking in water until maximum swelling showed no differences between thermally modified and furfurylated samples, but a subsequent test showed large differences in the rate of swelling for each wood type, with the furfurylated samples swelling very slowly. Long-term swelling in humid air showed similar results to soaking in water, but with the thermally modified samples having significantly greater dimensional stability than the furfurylated samples. Swelling for a short period in humid air showed no difference in swelling between the modified wood types, but there was a threefold reduction in swelling compared to the unmodified controls. For a more complete understanding of dimensional stability, several tests employing different test conditions should be used.

1 January 2010 in Maderas. Ciencia y Tecnología
Verified
Journal Article
Open access
PDF file
RSRosie Sargent
Rosie Sargent
SRS Riley
S Riley
LSL Schöttle
L Schöttle
Sorption behaviour of radiata pine has been investigated by weighing small specimens continuously during isothermal step changes in relative humidity. The use of wood specimens shorter in the longitudinal direction than the average tracheid length of radiata pine ensures that all tracheids in a specimen are exposed, reducing the effect of wood structure on bound water transport. The small size also allows the specimens to be prepared from a single band of earlywood or latewood. Using the dynamic sorption platform developed at Scion, a number of sorption experiments were undertaken comparing dynamic sorption behaviour of individual bands of earlywood and latewood, which had been heat treated to mimic the chemical changes that occur during high temperature drying. Diffusion coefficients and surface emission coefficients have been calculated from the sorption data, and are presented here. Earlywood and latewood had different sorption behaviour, but no measurable changes in sorption behaviour were seen with the different heat treatments. Diffusion coefficients were strongly dependent on moisture content.

23 June 2022 in Wood Science and Technology
Verified
Journal Article
Open access
PDF file
BDBernard S. W. Dawson
Bernard S. W. Dawson
RSRosie Sargent
Rosie Sargent
SRSteve G. Riley
Steve G. Riley
SHSean Husheer
Sean Husheer
ISIan G. Simpson
Ian G. Simpson
High pressure (20 MPa), cyclic, supercritical carbon dioxide (scCO2) treatments can reduce the moisture content of green Pinus radiata sapwood from 150–200% to 35–40%. Such treatments can be used as a dewatering pre-treatment before the kiln-drying of timber. Kiln-drying can utilise various temperature and humidity schedules, targeting around 10% moisture content, with a final stress-relieving steam-conditioning step. After scCO2 treatment and kiln-drying of samples, kiln brown stain was evaluated using the CIE L*a*b* colour space while drying stress was assessed by stress-cup measurements. The most significant results of scCO2 pre-treatment of Pinus radiata sapwood followed by kiln-drying plus steam-conditioning were as follows: Drying from green (36 h from a moisture content (MC) of 164%) using a conventional temperature schedule (90 °C/60 °C) took 2–5 times longer than kiln-drying scCO2 pre-treated boards (37.5% MC) to a target of 10% MC. Colour measurements proved that kiln brown stain does not occur. The use of a steam-conditioning step in reducing internal drying stresses was important irrespective of whether or not there was a scCO2 pre-treatment step. Over all drying schedule combinations, internal drying stress of both green and scCO2 pre-treated timber was similar after kiln-drying plus steam-conditioning. However, using only 90 °C/60 °C schedule data, with steam-conditioning, drying stresses were lower using kiln-drying without the scCO2 pre-treatment. This was surprising since the scCO2 step reduced the moisture content to around 37.5% without significant moisture gradients and so a secondary kiln-drying to 10% moisture content could have been expected to yield lower internal stress levels by preventing large moisture gradients to develop during drying. This result confirms the efficacy of the steam-conditioning step following standard kiln-drying. The colour data demonstrating the prevention of kiln brown stain using kiln-drying schedules offers a path to increasing timber quality for interior applications.


18 July 2022 in Wood Material Science & Engineering
Verified
Journal Article
Closed access
RSRosie Sargent
Rosie Sargent
CLC. A. Lenth
C. A. Lenth
Wood processing operations, such as timber drying, are increasingly employing high temperatures, and the development and optimisation of these operations is often reliant on modelling from experimental data. These model outputs are only accurate if the experimental data has been collected under similar conditions. In this research, the Modulus of Elasticity (MoE) and yield stress in compression and tension of two Pinus radiata trees are presented for a range of 6–30%MC between 20 and 150°C in the three grain directions. Results indicate that in all grain directions both MoE and yield stress decrease with increasing moisture content and increasing temperature, and this effect is more pronounced with the combination of high temperature and high moisture content. For both MoE and yield stress, differences were seen between testing in compression and in tension, and this relationship varied with grain direction and test conditions. This underscores the importance of accounting for the direction of applied forces when modelling the behaviour of wood. Overall, this data set indicates that yield stress and MoE can vary considerably according to temperature, moisture content, grain direction and the direction of the applied force.