The installation of underground trunk sewer lines in the Tuang formation of Kuching City, Malaysia, used trenchless technology in the form of the pipe-jacking method. The evaluation of pipe-jacking forces mainly involves empirical models developed for soils, with rather limited considerations for drives through weathered rock. Therefore, a novel approach is proposed to evaluate strength parameters by reconstituting and subsequently shearing scalped tunneling rock spoils in the direct shear apparatus. The direct shear results are then applied to a well-established pipe-jacking force model, which considers arching theory. The outcomes indicate that the backanalyzed frictional coefficients are not only reliable but also related to their surrounding geologies because of soil-structure interaction. This study also highlights the significance of lubrication and effect of rock arching in assessing jacking forces. The successful characterization of reconstituted tunneling rock spoils in this paper has shown potential use in assessing jacking forces during microtunneling works.
Prediction of jacking forces has been well-established for pipe-jacking drives traversing soils. However, the accrual of jacking forces for drives negotiating weathered rock formations has not been well understood. Three pipe-jacking drives in Kuching City, Malaysia spanning weathered lithological units of sandstone, phyllite and shale were studied. In the absence of in-situ pressuremeter testing during the investigation stage, tunneling rock spoils were collected and characterized through direct shear testing. The “generalized tangential” technique was applied to the nonlinear direct shear test results to obtain linear Mohr–Coulomb parameters, c′p and ϕ′p. This allowed for back-analysis of frictional coefficient, μavg through the use of a well-established predictive jacking force model. The reliability of using c′p, ϕ′p and μavg was assessed through 3D finite element modeling of the studied pipe-jacking drives. Based on these parameters, the results obtained from the numerical analyses of the studied pipe-jacking drives show good agreement with the jacking forces measured in-situ. The outcome of this research demonstrates that the derived strength parameters from direct shear testing of tunneling rock spoils has the potential to be used as reliable input parameters in finite element modeling to predict pipe-jacking forces in highly weathered geological formations
Several researchers have studied the behavior of particles during shearing to have better insight into the Mohr-Coulomb (MC) strength parameters. In most cases, the movements of particles along the shear band were studied by means of numerical modeling to obtain the velocities and directions of the soil particles. The use of a transparent shear box highlights the original enhancement and contribution in this paper to study the mechanical behavior of particles using particle image velocimetry (PIV) along the shear zone. Previous research using a transparent shear box suffered from several limitations such as obstructed view of the shear zone or using numerical simulation. The tested specimens consisted of sand and reconstituted rock spoils of metagreywacke and shale origins, which were classified according to their shapes and mineralogy contents. Particle shearing behavior was analyzed in detail at various stages throughout the direct shear tests with results complementing the PIV assessments. This novel interpretation technique successfully demonstrated how particle shapes and angularity, mineralogy, and effects of particle dilation and compression under shear can influence the strength parameters.
For the Kuching Wastewater Management System Phase 1 project in Kuching, Malaysia, 7·7 km of trunk sewer lines were constructed in the highly fractured, highly weathered Tuang Formation using a pipe-jacking method. The pipelines were founded at depths of up to 35 m below Kuching City, where the majority of the pipe-jacking activities would traverse the Tuang Formation. Jacking forces in highly fractured geology are not well understood as most jacking force models were derived for drives traversing soils. Therefore, a novel method was developed, whereby equivalent rock strength characteristics were interpreted from direct shear testing on reconstituted tunnelling rock spoils. Tangential peak strength parameters, [ ] and [ ], were developed from the nonlinear behaviour of the reconstituted spoils and applied to a well-established jacking model to assess arching and development of jacking forces from four documented drives. The back-analysed parameters μ avg and σ EV were used to demonstrate that geology had significantly affected the development of jacking forces. The back-analysis of the studied drives was successfully validated through finite-element modelling. This research shows that the developed parameters [ ] and [ ] and the back-analysed parameters μ avg and σ EV can be reliably used to predict jacking forces in highly fractured, highly weathered geology.