For the first time, we propose a stackable vertical channel-all-around (CAA) In–Ga–Zn-O field-effect transistor (IGZO FET) for high-density 4F 2 and long-retention 2T0C dynamic random access memory (DRAM) application. The device is fabricated in a back-end-of-line (BEOL) compatible process flow where the channel and gate-stack are deposited by plasma-enhanced atomic layer deposition (PEALD). The impact of IGZO cycle ratio and plasma power on the device’s electrical performance is studied. An optimized 50-nm channel-length CAA IGZO FET achieved ${I}_{ \mathrm{\scriptscriptstyle ON}} > 30 ~\mu \text{A}/\mu \text{m}$ and ${I}_{ \mathrm{\scriptscriptstyle OFF}}$ below $1.8\times10$ −17$\mu \text{A}/\mu \text{m}$ at ${V}_{\text {DS}} = 1$ V. A long retention of 300 s has been experimentally verified for the CAA IGZO 2T0C bit cell, making it a potential candidate for low-power 2T0C DRAM with ultralow refresh frequency. Finally, by monolithically stacking the vertical CAA IGZO FETs with 130-nm critical dimension (CD) to form 2T0C bit cells, we demonstrate the feasibility of the proposed BEOL-compatible 2T0C DRAM for further density scaling beyond 4F 2 .
In this work, the contact length scaling in dual-gate (DG) InGaZnO (IGZO) thin film transistors (TFTs) was experimentally investigated. With source/drain metal of Nickel (Ni) deposited in ultra-high vacuum condition (~ 8×10 -8 Torr), the contact resistance ( RC ) is achieved to be as low as 340 Ω·μm at an overdrive voltage of 2.5 V with contact resistivity ρ C = 1.72×10 -7 Ω·cm 2 . Scaling the contact length ( LC ) from 300 nm to 20 nm is then performed for both long-channel and short-channel DG IGZO TFTs and find that, in long-channel devices, the LC can be scaled down to 20 nm without noticeable performance degradation; in short-channel devices, a shorter LC (<30nm) would cause a pronounced performance degradation, including lower current density and worse subthreshold swing. Based on this observation, ultra-scaled high-performance DG IGZO TFTs are fabricated with a record-low contact pitch of 80 nm ( LC = 40 nm and LCH = 40 nm), achieving an ultra-high ION of 68.4 μA·μm -1 (at VG = VTH +1 V and VDS = 1 V) and a low SS of 83.4 mV·dec -1 .
This work reports the comprehensive study on asymmetric characteristic based on proposed stackable vertical Channel-All-Around (CAA) In-Ga-Zn-O field-effect transistors (IGZO FETs). Sufficient experimental data are analyzed for the reason of performance distinction between normal and reversed source/drain setup. Contact profile has great impacts on device characteristics such as short-channel effects and drain-induced barrier lowering (DIBL) due to different electric filed distributions in the IGZO channel near Schottky barrier. That is mainly caused by different etch process for upper and bottom electrodes, which doesn’t exist in planar structures. Furthermore, a 3-D technology computer-aided design (TCAD) device model is established. Interface defects are applied for slight variation in contact potential to verify the accuracy. Related analysis of contact barriers has been done based on simulation results. What’s more, channel length and etching depth of bottom electrode are also play a role in asymmetric characteristics, which could be applied as a reference to improve devices performance.
This letter reports a novel micro light-emitting diode ( $\mu $ LED) pixel driving circuit comprising ten amorphous indium gallium zinc oxide thin-film transistors (a-IGZO TFTs) and three capacitors. Hybrid PWM and PAM method is adopted to regulate gray-scales in the circuit using simple scan signals. Threshold voltage (Vth) shifts of TFTs are compensated in the pixel. To reduce the voltage drops caused by additional switching TFTs on the current path and save power, a matching TFT is used for the driving TFT Vth compensation. Simulation results indicate that the maximum error rates for emission time and current amplitude are -6.8% and 7.8% at a low gray level, respectively, under a Vth shift of 1 V. The power consumption of the circuit is successfully reduced thanks to the placement of only one TFT on the current path. Furthermore, we fabricated the pixel circuits which successfully demonstrates hybrid modulation.
In this letter, we demonstrate the coexistence of Schottky diode performance and resistance switching behavior based on TiN/a-IGZO/Cu device. Depending on the reverse voltage applied to the Cu electrode, the device itself can be obviously switched from diode mode to resistance switching mode. The device shows outstanding diode features with a large rectification ratio up to 3×106 at ±1 V and a high forward current density of 100 A/cm2 at +1 V. Furthermore, repeatable and stable switching behavior with low voltage has also been observed by increasing the reverse forming voltage. The physical model of Schottky barrier and conductive filament is proposed to explain the coexistence phenomenon. These achievements increase the application diversity of the metal oxide film and provide a great potential application in active-matrix flat-panel displays.
19 November 2019 in IEEE Transactions on Electron Devices