Acrylic resin is the most common fabricated material for denture bases. ZrO2 nanoparticles can be used as filler to strengthen the physical properties and inhibit the adhesion of acrylic resins. This study aimed to examine the growth of Candida albicans and porosity in reinforced acrylic resin with Zirconium Dioxide (ZrO2) nanoparticles at 2.5% and 5% a concentration targeted for denture bases application. A laboratory experiment study included twenty-seven disc-shaped samples which were divided into three groups: group I acrylic resin without ZrO2 nanoparticles (control), group II acrylic resin with 2.5% ZrO2 nanoparticles, and group III with 5% ZrO2 nanoparticle acrylic resin. Samples were collected by heat polymerization while porosity observations were done using primo zeizs starr (Nikon YS100) microscope at 100x magnification. Dilution test was implemented to assess Candida albican growth. One-way ANOVA and Post Hoc LSD test statistical analysis were performed to evaluate the data (p<0.05). The results indicated that the mean porosity values in the control group of 2.5% and 5% were 37.4 ± 3.5, 15.8 ± 3.3, 8.0 ± 2.0 respectively while the attachment of C. albicans was 0.832 ± 0.083, 0.536 ± 0.098, 0.218 ± 0.083. One-way ANOVA confirmed a significant effect (p<0.05). Similarly, Post Hoc LSD test reported significant difference (p<0.05). The results showed that acrylic resin reinforced with ZrO2 nanoparticles for heat-polymerized denture base effectively reduced porosity and C. albicans adhesion. Five percent of ZrO2 nanoparticle concentration presented greater porosity reduction compared to 2.5% ZrO2 and non-reinforced acrylic resin. Acrylic resin reinforced with ZrO2 nanoparticles in 2.5% and 5% concentration is fungistatic.
29 April 2021 in Research Journal of Pharmacy and Technology
Background: A residual monomer might have impact on the quality of acrylic resin since its caused allergic reactions and inflammation. Chitosan is a biocompatible material and potential to reduce residual monomers and ameliorate the impact strength of acrylic resin Objective of the study: To examine the effect of an acrylic resin matrix mixed with chitosan together with 1% and 2% acrylic acid as denture base and orthodontic material on residual monomers and impact strength. Methodology: There were 30 samples for the test analysis. The impact strength test sample formed with a plate size of 55 × 10 × 10mm, whereas the residual monomer test sample was prepared into powder. The test samples were divided into 3 groups, of 10 samples. Group 1 acrylic resin only, group 2 acrylic resin matrix mixed with chitosan and 1% acrylic acid, group 3 is the same as group 2 but with a concentration of 2% acrylic acid. Gas chromatography was used for measuring the residual monomers. The impact strength was tested by the Charpy impact. The data was evaluated using the ANOVA and correlation test. Results: There were significant differences (p < 0.05) in acrylic resin without addition with the matrix of acrylic resin with chitosan and acrylic acid 1% and 2% to the number of monomers and impact strength. Conclusion: The mixture of acrylic resin with chitosan and acrylic acid 1% and 2% can reduce the amount of residual monomer and increase the impact strength.
Objective This work aimed to determine the effect of adding chitosan and acrylic acid to acrylic resin denture base on the porosity of the material and the growth of Streptococcus mutans. Materials and Methods This study is an experimental laboratory research. Samples were divided into the following three groups (n = 10): group 1 was the control group, group 2 was the acrylic resin mixture with 1% chitosan and acrylate acid, and group 3 was the acrylic resin mixture with 2% chitosan and acrylate acid. S. mutans growth was tested using the dilution method, and porosity was examined using an optical microscope. Data were calculated by one-way analysis of variance (p < 0.05) and correlation analysis. Results The acrylic resin added with 2% chitosan and acrylic acid showed pores with an almost spherical shape and the smallest size. Significant difference (p < 0.05) was observed among all the groups. A positive and extremely strong correlation was found between porosity and S. mutans growth. Conclusion Chitosan and acrylic acid at 1 and 2% concentrations can be added to acrylic resin to minimize the porosity of the denture base and reduce the growth of S. mutans. A less porous denture is associated with a low S. mutans growth rate.
30 December 2022 in Majalah Kedokteran Gigi Indonesia
Polyetheretherketone (PEEK) and thermoplastics nylon are extensively composed as an alternative material for removable denture base. The primary difference between the two materials is associated with water absorption properties. The two materials interact with saliva and microorganisms during application in the oral cavity. Candida is predominantly reported in the cavity. The microorganism is distinguished by its hydrophobicity and ability to form biofilms. The objective of this study was to determine the differences between thermoplastic nylon and polyether-ether-ketone as removable denture materials in terms of hydrophobicity and Candida albicans biofilms. It is a laboratory experiment using 20 5 x 2 mm samples for the hydrophobicity test and Candida albicans biofilm. The hydrophobicity test was performed by determining the contact angle with a Goniometer and the WinDrop++ software. The biofilm test samples were divided into 4 groups, encompassing PEG 5% (negative control), PEEK treatment, thermoplastics nylon, and 0.12% chlorhexidine (control positive). The microdilution method was employed to examine biofilm formation. The results of the study were interpreted, and the data were analyzed by employing the t test. The research discovered significant differences in biofilm formation, large contact angle on PEEK and thermoplastics nylon (p < 0.05). Biofilm formation on thermoplastics is significantly larger than PEEK (p < 0.05). In conclusion, the contact angles of PEEK and thermoplastic nylon are incorporated in the partially wetted. Polyetheretherketone is involved in the non-producers of biofilms while thermoplastic nylon is categorized in of weak biofilm formers.
31 December 2023 in Majalah Kedokteran Gigi Indonesia