This study introduces an innovative phase-sensitive optical time-domain reflectometer (φ-OTDR) technology based on orthogonal frequency-division multiplexing (OFDM) and nonlinear frequency modulation (NLFM) pulse modulation sequences. The proposed approach addresses the inherent trade-offs among spatial resolution, frequency response range, and sensing distance that conventional φ-OTDR systems encounter. This method optimizes spatial resolution and sensing distance by modulating both the frequency and phase of optical pulses. Moreover, it enhances sidelobe suppression by adjusting the nonlinearity of frequency modulation, reducing interference between adjacent signals, and improving the signal-to-noise ratio (SNR). Additionally, orthogonal frequency-division multiplexing expands the frequency response range. This paper elucidates the fundamental principles and implementation of OFDM-NLFM time-domain pulse modulation techniques and designs, experimentally validates a φ-OTDR system based on this method, and conducts comprehensive testing and analysis of the system’s performance. The experimental results demonstrate that the proposed φ-OTDR system achieves an 11 m spatial resolution and a frequency response range of 1–10 kHz over a 16.3 km optical fiber, utilizing a 65 MHz frequency bandwidth with multiplexed signals across four frequencies. This innovative approach reduces hardware resource consumption, opening up promising prospects for various practical engineering applications in optical fiber sensing technology.

The large amount of sampled data in coherent phase-sensitive optical time-domain reflectometry (Φ-OTDR) brings heavy data transmission, processing, and storage burdens. By using the comparator combined with undersampling, we achieve simultaneous reduction of sampling rate and sampling resolution in hardware, thus greatly decreasing the sampled data volume. But this way will inevitably cause the deterioration of detection signal-to-noise ratio (SNR) due to the quantization noise’s dramatic increase. To address this problem, denoising the demodulated phase signals using compressed sensing, which exploits the sparsity of spectrally sparse vibration, is proposed, thereby effectively enhancing the detection SNR. In experiments, the comparator with a sampling parameter of 62.5 MS/s and 1 bit successfully captures the 80 MHz beat signal, where the sampled data volume per second is only 7.45 MB. Then, when the piezoelectric transducer’s driving voltage is 1 Vpp, 300 mVpp, and 100 mVpp respectively, the SNRs of the reconstructed 200 Hz sinusoidal signals are respectively enhanced by 23.7 dB, 26.1 dB, and 28.7 dB by using compressed sensing. Moreover, multi-frequency vibrations can also be accurately reconstructed with a high SNR. Therefore, the proposed technique can effectively enhance the system’s performance while greatly reducing its hardware burden.

In the domain of optical fiber distributed acoustic sensing, the persistent challenge of extending sensing distances while concurrently improving spatial resolution and frequency response range has been a complex endeavor. The amalgamation of pulse compression and frequency division multiplexing methodologies has provided certain advantages. Nevertheless, this approach is accompanied by the drawback of significant bandwidth utilization and amplified hardware investments. This study introduces an innovative distributed optical fiber acoustic sensing system aimed at optimizing the efficient utilization of spectral resources by combining compressed pulses and frequency division multiplexing. The system continuously injects non-linear frequency modulation detection pulses spanning various frequency ranges. The incorporation of non-uniform frequency division multiplexing augments the vibration frequency response spectrum. Additionally, nonlinear frequency modulation adeptly reduces crosstalk and enhances sidelobe suppression, all while maintaining a favorable signal-to-noise ratio. Consequently, this methodology substantially advances the spatial resolution of the sensing system. Experimental validation encompassed the multiplexing of eight frequencies within a 120 MHz bandwidth. The results illustrate a spatial resolution of approximately 5 m and an expanded frequency response range extending from 1 to 20 kHz across a 16.3 km optical fiber. This achievement not only enhances spectral resource utilization but also reduces hardware costs, making the system even more suitable for practical engineering applications.

A novel optical path matching method is provided to eliminate the optical path difference of the balanced detection fiber link. The noise floor is reduced by 8dB compared with that of the single photodetector output.

Since the effect of the facet braiding phenomenon, the display quality of reconstructed image degrades with increasing depth of field in tabletop three-dimensional light-field display. Here, to analysis the facet braiding, the imaging process of the tabletop 360-degree three-dimensional light-field display based on conical lens array is mathematically modeled. A viewpoint-fitting encoding algorithm is proposed to reduce the effect of the facet-braiding phenomenon and improve the range of depth of field, which is optimized to form the best synthetic encoded image by fitting the reconstructed image seen by the simulated human eye to the parallax image captured at the corresponding location. The effectiveness of the proposed optimization algorithm is verified by simulation analysis and optical experiments, respectively. In the experiment, the clear depth of field range of the display system is increased from 13 cm to 15 cm, and the visualization effect of the reconstructed three-dimensional image is enhanced.