Asphalt mixtures age during service in the field, primarily as the result of chemical changes in the bituminous binder phase. The ageing phenomenon changes the properties of the asphalt mixture, including the stiffness modulus, the resistance to deformation and the resistance to cracking, and it leads to surface weathering or erosion that often leads to pavement resurfacing. Consequently, many researchers have attempted to understand and to simulate the ageing of bituminous binders and asphalt mixtures in the laboratory. This review of bituminous binder and asphalt mixture ageing considers ageing simulation techniques, the effect of ageing on both bituminous binders and asphalt mixtures, the potential benefits of ageing inhibitors, and efforts to relate simulated laboratory ageing to observed field ageing. It is concluded that ageing has a significant effect on the properties of bituminous binders and asphalt mixtures, and that improved simulated ageing is important for comparing the effect of ageing on different materials and mixtures, as well as for quantifying the potential benefits of ageing inhibitors, which have generally been promising. It is also concluded that current ageing protocols are based on heat only, omitting the important contribution of solar radiation to the weathering and ageing of asphalt surfaces in the field. In the future, different simulated ageing protocols should be developed for binder and mixture samples. Similarly, a different ageing protocol is appropriate for understanding base-layer fatigue, compared to research on surface-layer weathering. Finally, it is concluded that a universal ageing protocol is unlikely to be found and that mixture- and climate-specific protocols need to be developed. However, given the importance of simulated ageing to asphalt researchers, the development of reliable, robust and calibrated laboratory ageing protocols is essential for the future.
Reliable accelerated simulation of asphalt aging is of significant interest to asphalt researchers and pavement practitioners alike. However, current laboratory aging protocols are either based on binder aging rather than mixture aging or use dry ovens to heat asphalt mixtures, omitting the important effects of UV radiation. Binder aging cannot take into account the interactions between the binder and aggregate phases during aging, while the omission of UV radiation ignores an important catalyst in the aging process. In this study, a comparison of the effect of conventional thermal oven aging to the combined effect of heat and ultraviolet irradiation on the resilient modulus and surface texture of dense-graded asphalt field cores and gyratory-compacted samples was undertaken. Significantly higher rates of modulus increase with aging time were measured for the samples aged by both heat and ultraviolet irradiation. The gyratory-compacted samples showed more realistic results in terms of surface texture compared to the field cores, likely due to the extraction of field cores from a small area of pavement that was subjected to concentrated pneumatic tyre rolling, which was not representative of typical asphalt construction. It was concluded that using aging indices, calculated as the ratio of the aged value to the initial value, is recommended for asphalt aging investigations. The findings of this study highlight the significance and importance of developing aging protocols that combine heat, ultraviolet irradiation, and any other environmental factors that may affect the aging behaviour of asphalt mixtures.
The reliable and representative ageing of asphalt samples in the laboratory is critically important to research on asphalt durability, waste material recycling and rejuvenation treatments. However, standard laboratory ageing protocols omit ultraviolet radiation and moisture, and are also based on a universally applied oven temperature and ageing duration. The aim of this research was to demonstrate the importance of ultraviolet radiation in laboratory asphalt aging, motivated by the need for more realistic ageing protocols. Asphalt cores were thermally aged in a standard laboratory oven for 98 days, while other cores were aged for the same period in a weathering chamber that combined thermal–oxidative (heat) and photo-oxidative (ultraviolet irradiation) aging. The bitumen was then extracted from the top, middle and bottom of each asphalt core, and tested for rheological, chemical, and compositional properties. The results were used to compare the effects of the aging protocols, and the effects of depth below the pavement surface. It was concluded that accelerated laboratory asphalt ageing must include photo-oxidation, in combination with thermal oxidation. It was also concluded that both chemical and rheological properties were effective indicators of extracted asphalt binder aging, although the rheological testing was preferred.
Asphalt pavements experience complex, depth-dependent aging driven by combined thermal-oxidative and UV photo-oxidative mechanisms. Current laboratory aging protocols often evaluate either only binder films or bulk mixtures exposed to thermal or photo oxidation; that is why this study aimed to contrast the differences in the chemical and rheological behaviors of both bitumen extractions and thin bitumen films exposed to heat only and heat combined with UV irradiation. Three dense-graded asphalt mixture samples were aged in an oven at 70 °C. For comparison, three samples with the same properties were aged in an ultraviolet (UV) weathering chamber at the same temperature but with UV irradiation at an intensity of 50 W/m2 for 98 days. Afterwards, samples were cut into three disks, and binder extractions from the top and middle disks were tested using a dynamic shear rheometer (DSR), saturates–aromatics–resins–asphaltenes (SARA) analysis, and Fourier-transform infrared spectrometry (FTIR) analysis. Samples of the same bituminous binder were also applied to steel plates at a thickness of 1 mm before being aged and tested under the same conditions. The results showed that UV irradiation plays a significant role in the aging process of bituminous binders in both asphalt mixtures and bitumen samples. In terms of DSR and SARA analysis results, extractions from the top disks of the UV- and oven-aged mixtures showed far more severe aging compared to the bituminous binder films, while the effect of pavement depth was found to have a more significant effect in samples that had been aged in the UV chamber. FTIR results followed the same trend, but the bituminous binder results were comparable to the results of the extractions from the aged mixture samples. It was concluded that binder aging research is better performed using binder specimens extracted from aged asphalt mixture samples, rather than thin films of binder, and that UV irradiation is essential for more realistic accelerated aging protocols.