We report chemical in situ deposition of conducting polymer poly (3,4-ethylenedioxythiophene) (PEDOT) on reduced graphene oxide (rGO) nanosheets through a simple hydrothermal polymerization method. The functional groups on graphene oxide (GO) were directly employed as an oxidant to trigger the polymerization of 3,4-ethylenedioxythiophene (EDOT), and the GO nanosheets were reduced into rGO accordingly in an aqueous environment. Well anchoring of ultrathin PEDOT on rGO through this oxidant-free method was confirmed by UV-Vis spectrum, FT-IR spectrum, SEM, and TEM analysis. The obvious enhancement of conductivity was observed after the covering of PEDOT on rGO, and this composite showed high conductivity about 88.5 S/cm. The electrochemical performance results revealed that rGO/PEDOT composite electrode exhibits high specific capacitance about 202.7 F/g. The good synergetic effect between PEDOT and rGO also makes sure highly stable reversibility of composite electrode during charging/discharging process, and more than 90% initial capacitance retains after 9000 times cycles. In addition, the electrode based on rGO/PEDOT deposited on the cotton fabric shows excellent flexible ability with the evidence that 98% of the initial capacitance of electrode maintained after three thousands of free bending, which shows promising energy storage performance for flexible devices.
In this paper, we demonstrate the preparation of a flexible poly (3,4-ethylenedioxythiophene) -poly (styrenesulfonate)/reduced graphene oxide (PEDOT-PSS/RGO) film with a layered structure via a simple vacuum filtered method as a high performance electrochemical electrode. The PEDOT-PSS/RGO films are characterized by scanning electron microscopy (SEM), X-ray diffraction, Raman spectroscopy, and Fourier transform infrared (FT-IR) spectrometry. The results indicate that a layer-ordered structure is constructed in this nanocomposite during the vacuum filtering process. The electrochemical performances of the flexible films are characterized by electrochemical impedance spectroscopy, cyclic voltammetry, and galvanostatic charge/discharge. The results reveal that a 193.7 F/g highly specific capacitance of nanocomposite film is achieved at a current density of 500 mA/g. This flexible and self-supporting nanocomposite film exhibits excellent cycling stability, and the capacity retention is 90.6 % after 1000 cycles, which shows promising application as high-performance electrode materials for flexible energy-storage devices.
10 August 2022 in ACS Applied Materials & Interfaces
We report the chemical in situ deposition of a porous conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT) on reduced graphene oxide (RGO) film as an efficient chemiresistor sensor platform for room temperature NH3 gas detection. A good covering of porous PEDOT on RGO was achieved through a simple baking treatment during the in situ polymerization of PEDOT. The good covering of porous PEDOT on the RGO surface was confirmed by SEM, UV-Vis spectra, and FT-IR spectra methods. The gas sensing performance revealed that, in contrast to bare RGO and common PEDOT, the porous PEDOT/RGO based gas sensor exhibited an obvious sensitivity enhancement as well as response/recovery performance. The large surface area and very open structure of the porous PEDOT resulted in an excellent synergistic effect between PEDOT and RGO during the gas sensing process. As a result of the uniform distribution of the PEDOT porous network on the RGO sheets, this nanocomposite based sensor also exhibited higher selectivity to NH3 in contrast to other reductive analyte gases.
In this paper, we demonstrated the utilization of reduced graphene oxide (RGO) Langmuir-Blodgett (LB) films as high performance hole injection layer in organic light-emitting diode (OLED). By using LB technique, the well-ordered and thickness-controlled RGO sheets are incorporated between the organic active layer and the transparent conducting indium tin oxide (ITO), leading to an increase of recombination between electrons and holes. Due to the dramatic increase of hole carrier injection efficiency in RGO LB layer, the device luminance performance is greatly enhanced comparable to devices fabricated with spin-coating RGO and a commercial conducting polymer PEDOT:PSS as the hole transport layer. Furthermore, our results indicate that RGO LB films could be an excellent alternative to commercial PEDOT:PSS as the effective hole transport and electron blocking layer in light-emitting diode devices.