To obtain the physical parameters and contact parameters of ramie stalk decorticating simulation, the structural dimensions, density, moisture content, elastic modulus, and contact parameters of the ramie stalk were measured in this study based on the phloem and xylem of the ramie stalk. The physical stacking angles of the phloem and xylem were measured by the cylinder lift method and the extraction of the partition method, respectively. The contact parameters between the xylem and phloem of the ramie stalk were directly calibrated. Additionally, the contact parameters of the phloem–phloem, phloem–Q235A steel, xylem–xylem, and xylem–Q235A steel were used as calibration objects, and the simulated stacking angle was used as the evaluation index. Then, the Plackett–Burman test was designed to screen for the parameters which were significantly affecting the simulated stacking angle. Furthermore, the steepest ascent test determined the optimal range of values for two significant parameters of the phloem and three significant parameters of the xylem. Based on the central composite design, the second-order regression equations between the significant parameters of the phloem and xylem and the stacking angle were established, respectively. The physical stacking angles of 37.93° for phloem and 27.17° for xylem were the target values to obtain the optimal parameter group. The results showed that the restitution, static, and rolling friction coefficients between the xylem and phloem were 0.60, 0.53, and 0.021, respectively. The static and rolling friction coefficients between the phloem and phloem were 0.41 and 0.056, respectively. The rolling friction coefficient between the xylem and Q235A steel was 0.033, and the static and rolling friction coefficients between the xylem and xylem were 0.44 and 0.016, respectively. The verification test showed that the relative error values were less than 2.11%, which further indicated that the modeling method and parameter calibration of the ramie stalk phloem and xylem models were accurate and reliable. They can be used for the subsequent calibration simulation tests of ramie stalk bonding parameters and ramie stalk decorticating simulations.

In order to reduce the chopping power consumption of a flat hob chopper (referred to herein as chopper) on the premise of ensuring the chopping effect of the chopper, the mathematical model of optimal design of chopper is established in this paper with the minimum chopping power as the objective. With the help of MATLAB software, the mathematical model is solved. The chopping power curves of each point on the chopper blade edge line before and after the optimization of structural parameters are generated. The results indicate that when the coordinate value of point A on the blade edge line on the Z axis is 0.7 m; the included angle between the bottom surface of the blade and the axis of the cutter roll is 6°. When the radius of the chopper is 0.11 m, the chopper can obtain the theoretical minimum chopping power. The analysis result of chopping power curve is the chopping power after structural parameter optimization is reduced by about 25.50% compared with that before optimization. The choppers before and after the optimization of structural parameters was trial manufactured and sequentially mounted on the performance test bench of the chopping system of the forage ramie harvester. The test results show the standard-length rate of ramie stalk chopped by the choppers before and after the optimization of structural parameters were 92.96% and 92.84%, respectively, which were extremely close to each other, indicating that the optimization of structural parameters has no influence on the chopping effect of the chopper. The chopping power of the chopper is reduced by 22.25% after optimization, which is close to the software analysis value (25.50%), indicating that the optimization result is accurate and reliable. This study can provide parameter foundation and an optimization method for lowering chopping power consumption of the chopper.

In order to solve the problems of high labor intensity and low production efficiency in the cultivation of hemp in hilly areas, the seed arrangement performance of self-propelled hemp seeders was studied. According to the cultivation mode of hemp for the fiber industry in Yunnan, Sichuan, and other hilly areas, the seed metering device for the hemp industry was designed, the seed metering mechanism of hemp was analyzed, and the theoretical value range of design parameters of its key components was determined. The row of kind of wheel speed is obtained by single factor experiment, hole diameter and hole depth and uniformity of the seed, the seed of change rule, on the basis of the quadratic regression orthogonal rotation combination test, two indexes of the regression model, using the regression model of the design parameter optimization, and seeder row of kind of verification test, the results show that: when the rotation speed of the metering wheel was 90.0 r/min, the diameter of the hole was 10.4 mm, and the depth of the hole was 6.4 mm, the coefficient of variation of seeding uniformity of seeding machine was less than 45%, and the coefficient of variation for consistency of seed quantity in each row was less than 8%. The operation of the self-walking industrial hemp seeder met the requirements of fiber industrial hemp planting in hilly areas.