Keyhole instability during laser welding and laser powder bed fusion (LPBF) can cause keyhole collapse and pore formation. Using high-speed x-ray imaging, we demonstrate that the flow vortex–induced protrusion on the rear keyhole wall is crucial in initiating keyhole instability. Applying a transverse magnetic field suppresses the keyhole instability by driving a secondary thermoelectric magnetohydrodynamics (TEMHD) flow that alters the net flow vortex. This minimizes protrusions and large-amplitude keyhole oscillations. The suppression effectiveness depends on the laser scanning direction relative to the magnetic field orientation because this controls the Seebeck effect–induced Lorentz force’s direction. We show that at LPBF length scales, electromagnetic damping is weak, and for alloys with a large Seebeck coefficient, TEMHD becomes the dominant mechanism controlling flow behind the keyhole.

This article presents a novel coupling of numerical techniques that enable three-dimensional convection-driven microstructure simulations to be conducted on practical time scales appropriate for small-size components or experiments. On the microstructure side, the cellular automata method is efficient for relatively large-scale simulations, while the lattice Boltzmann method provides one of the fastest transient computational fluid dynamics solvers. Both of these methods have been parallelized and coupled in a single code, allowing resolution of large-scale convection-driven solidification problems. The numerical model is validated against benchmark cases, extended to capture solute plumes in directional solidification and finally used to model alloy solidification of an entire differentially heated cavity capturing both microstructural and meso-/macroscale phenomena.

This article is devoted to the study of the tip shape of dendritic crystals grown from a supercooled liquid. The recently developed theory (Alexandrov & Galenko 2020 Phil. Trans. R. Soc. A 378 , 20190243. ( doi:10.1098/rsta.2019.0243 )), which defines the shape function of dendrites, was tested against computational simulations and experimental data. For a detailed comparison, we performed calculations using two computational methods (phase-field and enthalpy-based methods), and also made a comparison with experimental data from various research groups. As a result, it is shown that the recently found shape function describes the tip region of dendritic crystals (at the crystal vertex and some distance from it) well. This article is part of the theme issue ‘Transport phenomena in complex systems (part 1)’.

Large thermal gradients in the melt pool from rapid heating followed by rapid cooling in metal additive manufacturing generate large thermoelectric currents. Applying an external magnetic field to the process introduces fluid flow through thermoelectric magnetohydrodynamics. Convective transport of heat and mass can then modify the melt pool dynamics and alter microstructural evolution. As a novel technique, this shows great promise in controlling the process to improve quality and mitigate defect formation. However, there is very little knowledge within the scientific community on the fundamental principles of this physical phenomenon to support practical implementation. To address this multi-physics problem that couples the key phenomena of melting/solidification, electromagnetism, hydrodynamics, heat and mass transport, the lattice Boltzmann method for fluid dynamics was combined with a purpose-built code addressing solidification modelling and electromagnetics. The theoretical study presented here investigates the hydrodynamic mechanisms introduced by the magnetic field. The resulting steady-state solutions of modified melt pool shapes and thermal fields are then used to predict the microstructure evolution using a cellular automata-based grain growth model. The results clearly demonstrate that the hydrodynamic mechanisms and, therefore, microstructure characteristics are strongly dependent on magnetic field orientation. This article is part of the theme issue ‘Patterns in soft and biological matters'.

The fundamental mechanisms governing macroscopic freckle defect formation during directional solidification are studied experimentally in a Hele–Shaw cell for a low-melting point Ga-25 wt.% In alloy and modelled numerically in three dimensions using a microscopic parallelized Cellular Automata Lattice Boltzmann Method. The size and distribution of freckles (long solute channels, or chimneys) are shown to be strongly dependent on the thermal profile of the casting, with flat, concave and convex isotherms being considered. For the flat isotherm case, no large-scale freckles form, while for concave or convex isotherms, large freckles appear but in different locations. The freckle formation mechanism is as expected buoyancy-driven, but the chimney stability, its long-term endurance and its location are shown to depend critically on the detailed convective transport through the inter-dendritic region. Flow is generated by curved isopleths of solute concentration. As solute density is different from that of the bulk fluid, gravity causes ‘uphill’ or ‘downhill’ lateral flow from the sample centre to the edges through the mush, feeding the freckle. An excellent agreement is obtained between the numerical model and real-time X-ray observations of a solidifying sample under strictly controlled temperature conditions. This article is part of the theme issue ‘Heterogeneous materials: metastable and non-ergodic internal structures’.