Although lignin improves the strength and modulus of soil, it is less active when unmodified, and it exhibits more limited effects on soils in combination with traditional Ca-based curing agents. Lignin-solidified soil also exhibits deficiencies, such as poor durability under dry–wet cycling conditions, and thus, the amelioration effect is limited. This study investigated the enhancement of cement-solidified soil using hydroxylated lignin with sodium silicate and quicklime used as activators to improve the engineering performance and durability of the treated soil. Using respective cement, sodium silicate, quicklime, and lignin contents of 7%, 0.4%, 0.2%, and 0.2% with respect to the dry mass of the slag soil, the strength and cohesion of the composite-solidified soil were 1.5 times those of cement-solidified soil, whereas the internal friction angle increased by 5.1°. At a solidifying age of 14 d, the penetration resistance almost doubled, indicating a significant improvement in the bearing capacity of the soil. The results suggest that modified lignin-based admixtures may significantly enhance the performance of cement-solidified soil. The cement curing admixture used in this study provides theoretical and technological support for curing agent preparation and the utilization of slag.

Volatile organic compounds (VOCs) exert a serious impact on the environment and human health. The development of new technologies for the elimination of VOCs, especially those from non-industrial emission sources, such as indoor air pollution and other low-concentration VOCs exhaust gases, is essential for improving environmental quality and human health. In this study, a monolithic photothermocatalyst was prepared by stabilizing manganese oxide on multi-porous carbon spheres to facilitate the elimination of formaldehyde (HCHO). This catalyst exhibited excellent photothermal synergistic performance. Therefore, by harvesting only visible light, the catalyst could spontaneously heat up its surface to achieve a thermal catalytic oxidation state suitable for eliminating HCHO. We found that the surface temperature of the catalyst could reach to up 93.8 °C under visible light, achieving an 87.5% HCHO removal efficiency when the initial concentration of HCHO was 160 ppm. The microporous structure on the surface of the carbon spheres not only increased the specific surface area and loading capacity of manganese oxide but also increased their photothermal efficiency, allowing them to reach a temperature high enough for MnO_x to overcome the activation energy required for HCHO oxidation. The relevant catalyst characteristics were analyzed using XRD, measurement of BET surface area, scanning electron microscopy, HR-TEM, XPS, and DRS. Results obtained from a cyclic performance test indicated high stability and potential application of the MnO_x-modified multi-porous carbon sphere.

In the construction of urban underground shield tunnels, uneven deformation can easily occur when the shield passes through soft soil and other poor strata. Such deformation has a significant impact on surface settlement and may cause potential safety hazards to the surrounding existing buildings, directly affecting the safety of urban operation. When simulating and predicting surface settlements, the small-strain soil hardening model can more accurately characterize the mechanical parameters of soil. Nevertheless, its parameters are numerous and complicated to determine accurately, so parameter inversion is needed to determine the accurate parameters of the soft soil layer in order to more accurately predict the surface settlement. This study uses the EFAST method to analyse the sensitivity of the HSS model parameters of soft soil strata. It is determined that the parameters that have the most significant impact on the surface settlement are the reference tangent modulus, rebound modulus, and effective cohesion. Then, XGBoost’s fast calculation speed and high precision of SSA inversion are used to inverse and optimize the parameters with high sensitivity. Finally, according to the parameters of the soft soil layer obtained from inversion and measured data, the settlement deformation and safety behaviour of existing buildings are analysed. Combined with the actual shield tunnel project in a city along a river, the inversion calculation shows that the overall average error of the transverse monitoring section is 1.04 mm, and the average maximum error of each monitoring point in the overall shield process is 2.87 mm. The prediction effect is significantly improved compared with the original parameters. The accuracy of the inversion of soil layer parameters is verified from the perspective of time and space. The average settlement of the river embankment foundation is 2.5 mm. Compared with the original parameter data, the prediction results have been greatly improved, and the settlement deformation results are more consistent with the measured data.

Modified micromechanical bridging model is established with consideration of the fiber rupture effect at debonding and slipping stages. The bridging model includes the debonding and slipping rupture of fibers and establishes the fiber/matrix interfacial parameters (friction , chemical bonding force , slip-hardening coefficient ). A different interfacial bonding can cause fiber rupture. The influence of the interfacial conditions on the fiber rupture risk was investigated. In the modified bridging model, the effective bridging stress, the debonding rupture stress, and the slipping rupture stress were clearly identified. Finally, single-fiber pullout tests with different embedded lengths were carried out to validate the bridging model. The relationship between the fiber bridging stress and the crack opening predicted by the bridging model was consistent with the experimental results. This modified micromechanical bridging model can be used to quantitatively calculate the actual fiber bridging capacity and to predict the ductility of the high ductility cementitious composites reinforced by different types of fibers.