Nela Slavu

Ms. Nela Slavu

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 April 2022 in Processes
Verified
Journal Article
Open access
PDF file
NSNela Slavu
Nela Slavu
ABAdrian Badea
Adrian Badea
DFDinca Cristian Florian
Dinca Cristian Florian
In the context of climate change and the reduction in CO2 emissions from fossil fuel combustion, the integration of CO2 capture technologies in steam power plants is a key solution. The aim of this study was to analyze the use of ammonia, at different mass concentrations, in capturing post-combustion CO2 in a coal-fired power station and comparing it with the reference 30% MEA case. In this regard, a multi-criteria model was developed to establish the optimal solvent used, considering the least impact on technical performance, economic, and environmental indicators. As a result, the lowest CO2 capture cost was obtained for the CO2 capture process based on 7% NH3, with 59.07 €/tCO2. Integration of the CO2 capture process is more economically viable when the CO2 emissions tax is higher than 70 €/tCO2 for 7% NH3 and 15% NH3, 80 €/tCO2 for 5% NH3 and 30% MEA, and 90 €/tCO2 for 2% NH3. Regarding the overall efficiency, the energy penalty associated with the CO2 capture process integration varied between 15 and 35%, and the lowest value was obtained for 15% NH3. The GWP indicator ranged between 113 and 149 kg_CO2_eq/MWh for NH3 compared to MEA 133 kg_CO2_eq/MWh and the case with no CO2 capture was 823 kg_CO2_eq/MWh.

7 October 2023 in Processes
Verified
Journal Article
Open access
PDF file
NSNela Slavu
Nela Slavu
DFDinca Cristian Florian
Dinca Cristian Florian
The objective of this paper is to explore the utilisation of plastic waste via the gasification process to produce electricity with low carbon dioxide emissions. Worldwide, plastic production has increased, reaching 390 million tons in 2021, compared to 1.5 million tons in 1950. It is known that plastic incineration generates approximately 400 million tons of CO2 annually, and consequently, new solutions for more efficient plastic reuse in terms of emissions generated are still expected. One method is to use plastic waste in a gasifier unit and the syngas generated in a gas turbine for electricity production. The co-gasification process (plastic waste with biomass) was analysed in different ratios. Gasification was carried out with air for an equivalent ratio (ER) between 0.10 and 0.45. The volume concentration of CO2 in syngas ranged from 2 to 12%, with the highest value obtained when the poplar content in the mix was 95%. In this study, the option of pre- and post-combustion integration of the chemical absorption process (CAP) was investigated. As a result, CO2 emissions decreased by 90% compared to the case without CO2 capture. The integration of the capture process reduced global efficiency by 5.5–6.1 percentage points in a post-combustion case, depending on the plastic content in the mix.

7 February 2025 in Energies
Verified
Journal Article
Open access
PDF file
DFDinca Cristian Florian
Dinca Cristian Florian
NSNela Slavu
Nela Slavu
The cement industry is one of the industries with the highest contribution to global CO2 emissions due to its energy-intensive processes and the use of fossil fuels. This study evaluates the integration of the P2M-CC (power-to-methane with carbon capture) concept in cement plants to reduce the carbon footprint of the cement produced. Three cement plant modernization scenarios, involving replacing natural gas with synthetic methane obtained by methanation of green hydrogen and CO2 captured from the industrial process, were analyzed. The results show that integrating the P2M-CC concept reduced the CO2 emission factor from 789 kg/ton cement (baseline scenario) to 85 kg/ton (in all analyzed scenarios). However, the initial investment costs increased significantly by 5.8 times in S2.2, 5.2 times in S2.3, and 13 times in S2.1, compared to the baseline scenario, by adding the necessary equipment for electrolysis, methanation, and CO2 capture. On the other hand, operating costs decreased the most in S2.2, by 42.2% compared to the baseline scenario, while in S2.1, they decreased by 10.9%, and in S2.3, they increased by 141%. The ideal scenario (S2.2) showed the best economic and environmental performance, with an LCOC of 71 €/ton of cement and an NPV of 2609 million €, due to excess electricity produced by the wind plants without additional investment costs. In contrast, the complete scenario (S2.1), characterized by significant investments in wind power plants and CO2 capture technology, showed an LCOC of 297 €/ton of cement, while the realistic scenario (S2.3), with high operational costs, had an LCOC of 333 €/ton cement. Using synthetic methane in all proposed scenarios reduced fossil fuel dependency and CO2 emissions.

15 January 2025 in Preprints.org
Verified
Preprint
Open access
PDF file
DFDinca Cristian Florian
Dinca Cristian Florian
NSNela Slavu
Nela Slavu
The cement industry is recognized as an energy-intensive industry, and as a consequence of this, it is one of the industries that generate large amounts of CO2 into the environment. The global fight against climate change requires rethinking processes in such industries. The use of fossil fuels as a primary energy source and the cement production process make it one of the industries with the largest CO2 footprint. In this case, a sustainable solution, at least in the medium term, is to integrate the P2M-CC (Power - to - methane with carbon capture) concept, which involves replacing natural gas with synthetic methane obtained by methanization of green hydrogen and carbon dioxide captured from the industrial process. The paper analyzed three modernization scenarios of a cement plant with an annual production of 1,200,000 tons defined on the basis of techno-economic assumptions. It was observed that by integrating the P2M-CC concept in the initial process, the CO2 emission factor decreased from 789 (baseline scenario) to about 85 kg/ton of cement (proposed scenarios). From an economic point of view, the initial investment costs were significantly higher in the proposed scenarios than in the reference case due to the expansion of the plant by including electrolysis, methane, CO2 capture, and wind farm energy production. The costs were thus 5 to 13 times (€ 2.9 billion) higher than in the baseline scenario according to the assumptions underlying each scenario. In terms of operation and maintenance costs, the variation was totally different depending on the scenario analyzed, ranging from less than half of the costs of the baseline scenario to 2.4 times (€ 2.8 billion) higher. This variation depended to a large extent on the CO2 tax and the excess electricity used in the clinker process. The discounted cost per tonne of cement, LCOC, varied significantly for the 3 proposed scenarios, with the minimum value (about 58% lower than in the reference case) being obtained for the ideal scenario where the excess electricity covers the entire electricity needs of the cement plant processes. Despite the much higher initial investment and operating costs, the payback period was slightly longer than in the baseline case (5 vs. 3 years) due to the significantly higher net fees paid in the baseline scenario. In conclusion, the technical and economic improvement of the performance of the cement industry is dependent on the EU-wide regulation of CO2 taxes but also on the careful management of electricity generated by renewable energy sources.

12 September 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
NSNela Slavu
Nela Slavu
DFDinca Cristian Florian
Dinca Cristian Florian
The scope of this paper is to use plastic waste through the gasification process for producing electricity with low carbon dioxide emissions. Worldwide, plastic production increased, reaching 367 million tons in 2020, compared with 1.5 million tons in 1950. It is known that plastic incineration generates approximately 400 million tons of CO2 annually, and consequently, new solutions for a more efficient plastics reuse in terms of emissions generated are still expected. One method is to use plastic waste in a gasifier unit and the syngas generated in a gas turbine for electricity production. The co-gasification process (plastic waste with biomass) was analysed in different ratios. Gasification was carried out with air for an equivalent ratio (ER) between 0.10-0.45. The volume concentration of CO2 in syngas ranged from 2-12%, with the highest value obtained when poplar content in the mix was 95%. In this study, the option of pre- and post-combustion integration of the chemical absorption process (CAP) was investigated. Thus, CO2 emissions have decreased by 90% compared with the case without CO2 capture. By integrating the capture process, the global efficiency has reduced with 5.5 – 6.1 percentage points in a post-combustion case, according to the plastic content in the mix.

1 October 2019
Verified
Conference Paper
Closed access
OPOana Penu
Oana Penu
DFDinca Cristian Florian
Dinca Cristian Florian
NSNela Slavu
Nela Slavu
ABAdrian Badea
Adrian Badea
Physical absorption method is used predominantly prior to the electricity generation in different energy systems. In these cases the carbon dioxide is separated from the synthesis gas obtained as a result of coal or biomass/waste gasification. For Rectisol process, the carbon dioxide capture performance using physical solvents (e.g. methanol, methylpyrrolidone, etc.) increases with the pressure (usual: 20-50 bar) and decreases with the temperature (usual: -10 .. -60 °C) inside the absorption unit. In some cases, in order to increase the solubility of the acid gases (CO2, H2S) and reduce the physical solvent flow, it is necessary that the physical absorption process takes place at temperatures below the ambient temperature. In this case, it’s required to cool the synthesis gas before entering the absorption column, then reheating it before injection into the gas turbine (or other energy systems). The additional processes of the heating and cooling steps of the synthesis gas as well as the cooling of the physical solvent before the absorption column leads to energy penalties (additional electricity/thermal energy consumption) and consequently to the significant reduction of the physical absorption technology performance. In this paper an analysis of the technical effects of different refrigeration fluids on the Rectisol process is developed. The energy consumption in the Rectisol process reduces drastically the performances of the energy system.