The present study investigates the mechanical and corrosion properties of reinforced 6061[ ]T6 aluminum samples after friction stir processing. Three different composites are fabricated: one without any powder and the others with micrometer and nanometer alumina powder (Al2O3) as reinforcing particles. The hardness, tensile, and potentiodynamic polarization tests are performed to compare the new samples with the base metal. The results show that friction stir processing has increased the tensile and ultimate strength of the composites by an average of 181% compared to the base metal which is due to the microstructure changes including grain distribution refinement and the elimination of defects and micro-voids through localized plastic deformation. The strength of the composites with additives is significantly affected by the size of the particles. The hardness of the processed samples has also increased compared to the base metal by 200%. Despite these enhancements, the corrosion resistance of new samples has decreased by 70%, which can be due to the numerous dislocations in the stress-induced stir zone, creating lattice deformations and causing the breakdown of the passive protective layer. The analysis of fracture surface topography through a Fractography method revealed a specific anaglyph consisting of dimples of various shapes, sizes, and dispersion and further confirmed the tensile test results.
The present study investigates the mechanical and corrosion properties of reinforced 6061TT6 Aluminum samples after friction stir processing. Three different composites are fabricated: one without any powder and the others with micrometer and nanometer alumina powder (h) as reinforcing particles. The hardness, tensile, and Potentiodynamic polarization tests are performed to compare the new samples with the base metal. The results show that friction stir processing has increased the tensile and ultimate strength of the composites by an average of 181 % compared to the base metal. The strength of the composites with additives is significantly affected by the size of the particles. The hardness of the processed samples has also increased compared to the base metal by 200 %. Despite these enhancements, corrosion resistance of new samples has decreased, which can be due to the numerous dislocations in the stress-induced stir zone, creating lattice deformations and causing the breakdown of the passive protective layer. The analysis of fracture surface topography through a Fractography method revealed a specific anaglyph consisting of dimples of various shapes, sizes, and dispersion and further confirmed the tensile test results.
This article presents new hexagonal and pentagonal PEM fuel cell models. The models have been optimized after achieving improved cell performance. The input parameters of the multi-objective optimization algorithm were pressure and temperature at the inlet, and consumption and output powers were the objective parameters. The output data of the numerical simulation has been trained using deep neural networks and then modeled with polynomial regression. The target functions have been extracted using the RSM (Response Surface Method), and the targets were optimized using the multi-objective genetic algorithm (NSGA-II). Compared to the base model, the optimized Pentagonal and Hexagonal models increase the output current density by 21.8% and 39.9%, respectively.
This article presents new PEM fuel cell models with hexagonal and pentagonal designs. After observing cell performance improvement in these models, we optimized them. Inlet pressure and temperature were used as input parameters, and consumption and output power were the target parameters of the multi-objective optimization algorithm. Then we used artificial intelligence techniques, including deep neural networks and polynomial regression, to model the data. Next, we employed the RSM (Response Surface Method) method to derive the target functions. Furthermore, we applied the NSGA-II multi-objective genetic algorithm to optimize the targets. Compared to the base model (Cubic), the optimized Pentagonal and Hexagonal models averagely increase the output current density by 21.819\% and 39.931\%, respectively.
The present study investigates the mechanical and corrosion properties of reinforced 6061-T6 Aluminum samples after friction stir processing. Three different composites are fabricated: one without any powder and the others with micrometer and nanometer alumina powder ({Al}_2O_3) as reinforcing particles. The hardness, tensile, and Potentiodynamic polarization tests are performed to compare the new samples with the base metal. The results show that friction stir processing has increased the tensile and ultimate strength of the composites by an average of 181 % compared to the base metal. The strength of the composites with additives is significantly affected by the size of the particles. The hardness of the processed samples has also increased compared to the base metal by 200 %. Despite these enhancements, corrosion resistance of new samples has decreased, which can be due to the numerous dislocations in the stress-induced stir zone, creating lattice deformations and causing the breakdown of the passive protective layer. The analysis of fracture surface topography through a Fractography method revealed a specific anaglyph consisting of dimples of various shapes, sizes, and dispersion and further confirmed the tensile test results.
After discussion, the authors have collectively decided to retract this preprint in order to ensure the accuracy and completeness of the data it presents.