Kenichiro Takeishi

Prof. Dr. Kenichiro Takeishi

Tokushima Bunri University, 1314-1, Shido, Sanuki City, Kagawa 769-2193, Japan
orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
KTKenichiro Takeishi
Kenichiro Takeishi
RKRobert Krewinkel
Robert Krewinkel
In the coming carbon-neutral era, industrial gas turbines (GT) will continue to play an important role as energy conversion equipment with high thermal efficiency and as stabilizers of the electric power grid. Because of the transition to a clean fuel, such as hydrogen or ammonia, the main modifications will lie with the combustor. It can be expected that small and medium-sized gas turbines will burn fewer inferior fuels, and the scope of cogeneration activities they are used for will be expanded. Industrial gas turbine cycles including CCGT appropriate for the carbon-neutral era are surveyed from the viewpoint of thermodynamics. The use of clean fuels and carbon capture and storage (CCS) will inevitably increase the unit cost of power generation. Therefore, the first objective is to present thermodynamic cycles that fulfil these requirements, as well as their verification tests. One conclusion is that it is necessary to realize the oxy-fuel cycle as a method to utilize carbon-heavy fuels and biomass and not generate NOx from hydrogen combustion at high temperatures. The second objective of the authors is to show the required morphology of the cooling structures in airfoils, which enable industrial gas turbines with a higher efficiency. In order to achieve this, a survey of the historical development of the existing cooling methods is presented first. CastCool® and wafer and diffusion bonding blades are discussed as turbine cooling technologies applicable to future GTs. Based on these, new designs already under development are shown. Most of the impetus comes from the development of aviation airfoils, which can be more readily applied to industrial gas turbines because the operation will become more similar. Double-wall cooling (DWC) blades can be considered for these future industrial gas turbines. It will be possible in the near future to fabricate the DWC structures desired by turbine cooling designers using additive manufacturing (AM). Another conclusion is that additively manufactured DWC is the best cooling technique for these future gas turbines. However, at present, research in this field and the data generated are scattered, and it is not yet possible for heat transfer designers to fabricate cooling structures with the desired accuracy.

25 November 2022 in Energies
Verified
Journal Article
Open access
PDF file
KTKenichiro Takeishi
Kenichiro Takeishi
Photovoltaics and wind power are expected to account for a large share of power generation in the carbon-neutral era. A gas turbine combined cycle (GTCC) with an industrial gas turbine as the main engine has the ability to rapidly start up and can follow up to load fluctuations to smooth out fluctuations in power generation from renewable energy sources. Simultaneously, the system must be more efficient than today’s state-of-the-art GTCCs because it will use either Carbon dioxide Capture and Storage (CCS) when burning natural gas or hydrogen/ammonia as fuel, which is more expensive than natural gas. This paper describes the trend of cooled turbine rotor blades used in large industrial gas turbines that are carbon neutral. First, the evolution of cooled turbine stationary vanes and rotor blades is traced. Then, the current status of heat transfer technology, blade material technology, and thermal barrier coating technology that will lead to the realization of future ultra-high-temperature industrial gas turbines is surveyed. Based on these technologies, this paper introduces turbine vane and blade cooling technologies applicable to ultra-high-temperature industrial gas turbines for GTCC in the carbon-neutral era.

27 September 2013 in Journal of Turbomachinery
Verified
Journal Article
Closed access
PDF file
KTKenichiro Takeishi
Kenichiro Takeishi
MKMasaharu Komiyama
Masaharu Komiyama
YOYutaka Oda
Yutaka Oda
YEYuta Egawa
Yuta Egawa

20 May 2013 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
KTKenichiro Takeishi
Kenichiro Takeishi
YOYutaka Oda
Yutaka Oda
YMYoshiaki Miyake
Yoshiaki Miyake
YMYusuke Motoda
Yusuke Motoda
Local endwall heat transfer characteristics and overall pressure loss of normal and inclined pin fins arrayed in rectangular ducts with flat and wavy endwalls have been investigated to improve the cooling efficiency of jet engine combustor liners. The detailed time-mean local Nusselt number profiles were measured using a naphthalene sublimation method based on the heat/mass transfer analogy. Four kinds of angled pin fins (−45, 0, and +45 deg with a flat endwall, and −45 deg with a wavy endwall) were tested and compared with each other. As a result, the average heat transfer coefficient on the flat endwall of normal pin fins was higher than that of the angled pin fins. The average heat transfer coefficient of −45-deg inclined pin fins with a wavy endwall is the same or a little higher than the heat transfer coefficient of those with a flat endwall; however, the pressure loss of the −45-deg inclined pin fins with a wavy endwall is less than the pressure loss of those with a flat endwall. Corresponding numerical simulations using large eddy simulation (LES) with the mixed time scale (MTS) model have been also conducted at Red = 1000 for fully developed regions, and the results have shown good quantitative agreement with mass transfer experiments. It can be concluded that wavy endwalls can realize better heat transfer with less pressure loss as long as the aim consists in enhancing endwall heat transfer in inclined pin-fin channels.

1 January 2011
Verified
Conference Paper
Closed access
PDF file
KTKenichiro Takeishi
Kenichiro Takeishi
YOYutaka Oda
Yutaka Oda
YEYuta Egawa
Yuta Egawa
SHSatoshi Hada
Satoshi Hada
A new film cooling concept has been developed by managing the swirled film coolant induced inside a hexagonal plenum by two slant impingement jets, which are inclined at α degree toward the vertical direction and installed in a staggered position on the plenum chamber wall. Film cooling tests have been conducted by using a circular film cooling hole model mounted on a low speed wind tunnel. Heat transfer coefficient distributions of inclined jet impingements in a closed cavity was measured by naphthalene sublimation method and the film cooling effectiveness on the surface of the wind tunnel was measured by pressure sensitive paint (PSP). It appeared from experimental results that the swirled film coolant flow deteriorated the film cooling effectiveness at low swirl number but improved it at high swirl number. To investigate the mechanism of the improved film cooling effectiveness by the swirled coolant, the spatial distribution of the film cooling effectiveness and flow field were measured by laser induced fluorescence (LIF) and particle image velocimetry (PIV), respectively. The coolant jet penetration into mainstream is suppressed by the strong swirling motion of the coolant. As a result the film cooling effectiveness distribution on the wall keeps higher value behind the cooling hole over a long range. Additionally, kidney vortex structure was disappeared at high swirl number.

1 January 2011 in The Proceedings of the Thermal Engineering Conference
Verified
Journal Article
Closed access
KTKenichiro Takeishi
Kenichiro Takeishi
YOYutaka Oda
Yutaka Oda
YEYuta Egawa
Yuta Egawa