The adsorption of arsenic [arsenite (As(III)) and arsenate (As(V))] onto aluminum substituted nickel ferrite (Ni–Al–Fe) which is a ternary metal oxide nano adsorbent is evaluated. Qualitative and quantitative studies were performed to understand the adsorption phenomenon. The qualitative studies for both adsorbent and arsenic adsorbed samples were evaluated using FT-IR, Raman and XPS techniques and the quantitative studies were carried out using ICP-OES technique. The results reveal that the maximum adsorption capacities of Ni–Al–Fe adsorbent are around 114 and 103 mg g−1 for As(III) and As(V) species in 100 ppm arsenic equilibrium concentration (Ce) systems. Also, at low initial concentrations (100 and 500 ppb) a better adsorption phenomenon (i.e. WHO guidelines limit of 10 ppb) for the As(V) species onto the Ni–Al–Fe adsorbent was observed. In addition the kinetics of adsorption, and effect of concentration and pH on the adsorption phenomena have been detailed.
21 October 2020 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Over the last decade, FRP composites have seen increased use in many applications, where an optimum combination of light-weight, better wear resistance and excellent mechanical properties have attributed to their uses in different engineering segments. In this study, Mechanical and tribological properties of woven glass fiber-reinforced epoxy (GFRE) composites with and without graphene nanoplatelets (GNPs) were obtained and correlated. The results of the unmodified GFRE laminates (neat GFRE samples) were compared with those containing 0.5 and 1 wt. % of GNPs (modified samples). Wear resistance of the GFRE composite samples increased with an increase in the GNPs content in the epoxy matrix as obtained by experiments conducted on the Pin-on-disc tribometer. Wear tests showed a considerable reduction in wear rate from 4.54 × 10−11 m3/Nm (neat GFRE) to the lowest value of 2.31 × 10−11 m3/Nm, by adding 1 wt.% GNPs. Further, it was observed that the addition of 0.5 and 1.0 wt. % of GNPs in the base material lowered the coefficient of friction (µ) by about 4% and 18%, respectively, for abrading distance of 200 m, due to the self-lubricating nature of GNPs. The wear mechanisms and transfer film formation were examined using scanning electron microscopy (SEM) equipped with energy dispersive spectroscopy (EDS) analysis.
19 July 2019 in Journal of Physics D: Applied Physics
In this article, a textile-based metamaterial with broadband microwave absorption was developed using a screen printing technique. The metamaterial has over 90% absorption from 7.39 GHz to 18 GHz. The metamaterial consists of a top layer of the printed structure of commercial conductive inks on various kinds of clothes, which is separated from a conductive ground plane with flexible dielectric foam of 3.2 mm thickness. The metamaterial absorber was simulated using ANSYS HFSS software for various thicknesses of the printed ink. It was observed that the absorption band varies with variation in printed thickness, and the optimized printed thickness was found to be about 50 µ m. With the increase in printed thickness, the absorption shifts from broadband to narrow band. To achieve the optimum thickness in fabrication, statistically designed experiments were conducted to study the variation of printed thickness and width with different kinds of clothes and substrates (FR4, plain weave cotton cloth, and twill weave cotton cloth), mesh number of the screen (50–110) and the number of passes (1–3). Substrate material and the number of passes were found to be the most significant factors that affect the printed width resolution and thickness. Rigid copper foil and printed cloth could both be used as the ground plane. A complete, flexible absorber was fabricated using printed cloth as the ground plane. The microwave response (absorption) of all the fabricated absorbers was measured and found to be in agreement (more than 90%) with the simulation. Further, the fabricated absorber on the cloth substrate was also made hydrophobic by treating it with polydimethylsiloxane.
The present work discusses the effect of the pearlitic morphology with varying fineness on the cavitation erosion behavior of eutectoid rail steel. Cavitation erosion of three different types of the pearlitic steels (furnace-cooled, air-cooled, and forced-air-cooled) consisting of coarse, fine, and very fine microstructures were tested in 3.5% NaCl solution and compared with that of the as-received pearlitic rail steel. The variation in the mean depth of erosion (MDE) and mean depth erosion rate (MDER) with erosion time was analyzed. Furthermore, the cavitation erosion resistance of the as-received, the air-cooled, and the forced-air-cooled was found to be 1.03, 1.51, and 2.14 times better than the furnace-cooled pearlitic steel, respectively. It was concluded that the cavitation erosion resistance of the pearlitic steel increased with the increase in the fineness of the microstructure.