The test data of metals, brittle materials and polymers in high, medium and low strain-rate range were summarized. It was found that the dynamic strength or yield stress of these materials was not sensitive to strain-rate in the low and high strain-rate range (corresponding to weak sensitivity area and saturated zone). But in the medium strain-rate range (strong sensitivity area), the dynamic strength or yield stress of these materials was extremely sensitive to strain-rate. The strain-rate effect function in classic Johnson-Cook constitutive model could not describe these phenomena in the range of low to high strain-rate. Therefore, the strain-rate effect function in classic Johnson-Cook constitutive model has been modified to a strain-rate effect expression which is suitable for different materials. This new model can better describe the phenomena of the weak sensitivity area, strong sensitivity area and saturated zone. With this model, the fitted curves are in good agreement with the test data, and the parameters are different for different materials. Finally, the fitting parameters are given.
In mining engineering, the in situ stress changes with the stress induced by the surrounding mining activities. It positively or negatively affects the propagation of ultrasonic guided waves in rockbolts. Therefore, the effect of in situ stress in rockbolt support was determined by applying confining pressure and pull-out load in a laboratory test and using ultrasonic guided waves to test the rockbolt. Furthermore, the propagation law of ultrasonic guided waves and bond quality of the rockbolt under the interaction of the pull-out load and confining pressure were studied. Numerical simulations were performed to deduce the guided wave propagation process in grouted systems, and the influencing mechanism of the pull-out load and confining pressure on the guided wave propagation was discussed. The laboratory test and numerical simulation results show that the confining pressure weakens the guided wave propagation without pull-out load. Under the same pull-out load, the guided wave propagation gradually strengthens with increasing confining pressure. A larger confining pressure weakens the weakening effect of the pull-out load and suppresses the discreteness of the guided wave propagation. Under the same confining pressure, the guided waves did not diffract well into the cement mortar and concrete with increasing pull-out load, the confining pressure restricted the radial vibration of the guided waves, and the guided wave propagation law weakened. Thus, the pull-out load plays a weakening role in the propagation law of ultrasonic guided waves.
31 August 2022 in Advances in Materials Science and Engineering
In grouted rock bolt systems, bond defects often occur, which seriously affects the safety of rock mass structures. Therefore, in this study, based on the existence of bond defects, laboratory tests were conducted to detect the location and length of bond defects and study the guided wave propagation in grouted rock bolt systems under different pullout loads. The guided wave signal was analysed in the time domain and frequency domain. In addition to the laboratory test, a numerical simulation of the effect of different bond defect locations on ultrasonic guided wave propagation in rock bolts was conducted using a damage-based model. The influence mechanism of bond defects on guided wave propagation under different pullout loads was explored. The study confirmed that there existed a stress platform in the rock bolt at the bond defect under a pullout load. The location and length of the bond defect could be detected by the stress platform and guided wave. The debonding length increased exponentially with the amplitude ratio (Q) of low frequency to high frequency, and the Q value could be used as the quantitative index of debonding length. As the pullout load increased, the impedance mismatch between the rock bolt and cement mortar (defect) increased, and the guided wave propagation in grouted rock bolt systems was irregular. The pullout load weakened the guided wave propagation law. The larger the pullout load is, the greater the weakening effect is.
10 February 2025 in Tunnelling and Underground Space Technology
Rockbolts are often subjected to loads during service, and the load transfer behaviour of rockbolts is very important. Therefore, in this study, pullout tests were performed on two kinds of rockbolt systems, with and without defects, and the load transfer behaviour and failure modes were analysed. According to the load transfer process between the rockbolt and cement mortar interface, a bond-slip model considering the yield of the rockbolt was proposed, and the nonlinear behaviour in the softening stage was considered. The test results showed that the evolution of the interface load between the rockbolt and cement mortar in the grouted rockbolt systems without defects underwent four stages of gradual failure, namely, elasticity, yield, softening, and complete slip, and its failure mode involved the rockbolt being pulled out accompanied by splitting cracks and tensile cracks on the concrete surface. The proposed bond-slip models considering the nonyielding and yielding of the rockbolt can accurately reflect the actual load transfer behaviour of a fully grouted rockbolt.