Airborne measurements of methane emissions from oil and gas infrastructure were completed over two regions of Alberta, Canada. These top-down measurements were directly compared with region-specific bottom-up inventories that utilized current industry-reported flaring and venting volumes (reported data) and quantitative estimates of unreported venting and fugitive sources. For the 50 × 50 km measurement region near Red Deer, characterized by natural gas and light oil production, measured methane fluxes were more than 17 times greater than that derived from directly reported data but consistent with our region-specific bottom-up inventory-based estimate. For the 60 × 60 km measurement region near Lloydminster, characterized by significant cold heavy oil production with sand (CHOPS), airborne measured methane fluxes were five times greater than directly reported emissions from venting and flaring and four times greater than our region-specific bottom up inventory-based estimate. Extended across Alberta, our results suggest that reported venting emissions in Alberta should be 2.5 ± 0.5 times higher, and total methane emissions from the upstream oil and gas sector (excluding mined oil sands) are likely at least 25–50% greater than current government estimates. Successful mitigation efforts in the Red Deer region will need to focus on the >90% of methane emissions currently unmeasured or unreported.
1 January 2005 in Proceedings of the Combustion Institute
Airborne LiDAR measurements, parallel controlled releases, and on-site optical gas imaging (OGI) survey and pneumatic device count data from 1 year prior, were combined to derive a new measurement-based methane inventory for oil and gas facilities in British Columbia, Canada. Results reveal a surprising distinction in the higher magnitudes, different types, and smaller number of sources seen by the plane versus OGI. Combined data suggest methane emissions are 1.6–2.2 times current federal inventory estimates. More importantly, analysis of high-resolution geo-located aerial imagery, facility schematics, and equipment counts allowed attribution to major source types revealing key drivers of this difference. More than half of emissions were attributed to three main sources: tanks (24%), reciprocating compressors (15%), and unlit flares (13%). These are the sources driving upstream oil and gas methane emissions, and specifically, where emerging regulations must focus to achieve meaningful reductions. Pneumatics accounted for 20%, but this contribution is lower than recent Canadian and U.S. inventory estimates, possibly reflecting a growing shift toward more low- and zero-emitting devices. The stark difference in the aerial and OGI results indicates key gaps in current inventories and suggests that policy and regulations relying on OGI surveys alone may risk missing a significant portion of emissions.
25 April 2023 in Communications Earth & Environment
Critical mitigation of methane emissions from the oil and gas (OG) sector is hampered by inaccurate official inventories and limited understanding of contributing sources. Here we present a framework for incorporating aerial measurements into comprehensive OG sector methane inventories that achieves robust, independent quantification of measurement and sample size uncertainties, while providing timely source-level insights. This hybrid inventory combines top-down, source-resolved, multi-pass aerial measurements with bottom-up estimates of unmeasured sources leveraging continuous probability of detection and quantification models for a chosen aerial technology. Notably, the technique explicitly considers skewed source distributions and finite facility populations that have not been previously addressed. The protocol is demonstrated to produce a comprehensive upstream OG sector methane inventory for British Columbia, Canada, which while approximately 1.7 times higher than the most recent official bottom-up inventory, reveals a lower methane intensity of produced natural gas (<0.5%) than comparable estimates for several other regions. Finally, the method and data are used to upper bound the potential influence of source variability/intermittency, directly addressing an open question in the literature. Results demonstrate that even for an extreme case, variability/intermittency effects can be addressed by sample size and survey design and have a minor impact on overall inventory uncertainty.
A technique of diffuse-light two-dimensional line-of-sight attenuation (diffuse 2D-LOSA) is described and demonstrated that achieves very high levels of sensitivity in transmissivity measurements (optical thicknesses down to 0.001) while effectively mitigating interferences due to beam steering. An optical system is described in which an arc lamp coupled with an integrating sphere is used as a source of diffuse light that is imaged to the center of the particulate laden medium. The center of the medium is then imaged onto a CCD detector with 1:1 magnification. Comparative measurements with collimated 2D-LOSA in nonpremixed flames demonstrate the accuracy and improved optical noise rejection of the technique. Tests in weakly sooting, nonpremixed methane–air flames, and in high pressure methane–air flames, reveal the excellent sensitivity of diffuse 2D-LOSA, which is primarily limited by the shot noise of the lamp and CCD detector.