Sasha Hoshian

Dr. Sasha Hoshian

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 December 2014 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
SHSasha Hoshian
Sasha Hoshian
VJVille Jokinen
Ville Jokinen
VSVilleseveri Somerkivi
Villeseveri Somerkivi
ALArcot R. Lokanathan
Arcot R. Lokanathan
SFSami Franssila
Sami Franssila
Superhydrophobic surfaces without low surface-energy (hydrophobic) modification such as silanization or (fluoro)polymer coatings are crucial for water-repellent applications that need to survive under harsh UV or IR exposures and mechanical abrasion. In this work, robust low-hysteresis superhydrophobic surfaces are demonstrated using a novel hierarchical silicon structure without a low surface-energy coating. The proposed geometry produces superhydrophobicity out of silicon that is naturally hydrophilic. The structure is composed of collapsed silicon nanowires on top and bottom of T-shaped micropillars. Collapsed silicon nanowires cause superhydrophobicity due to nanoscale air pockets trapped below them. T-shaped micropillars significantly decrease the water contact angle hysteresis because microscale air pockets are trapped between them and can not easily escape. Robustness is studied under mechanical polishing, high-energy photoexposure, high temperature, high-pressure water shower, and different acidic and solvent environments. Mechanical abrasion damages the nanowires on top of micropillars, but those at the bottom survive. Small increase of hysteresis is seen, but the surface is still superhydrophobic after abrasion.

1 July 2016 in Soft Matter
Verified
Journal Article
Open access
PDF file
SHSasha Hoshian
Sasha Hoshian
VJV. Jokinen
V. Jokinen
SFSami Franssila
Sami Franssila
We introduce a new type of hybrid material: a nanostructured elastomer covered by a hard photoactive metal-oxide thin film resembling the exoskeleton of insects. It has extreme water repellency and fast self-recovery after damage. A new fabrication method for replicating high aspect ratio, hierarchical re-entrant aluminum structures into polydimethylsiloxane (PDMS) is presented. The method is based on a protective titania layer deposited by atomic layer deposition (ALD) on the aluminum template. The ALD titania transfers to the elastomeric scaffold via sacrificial release etching. The sacrificial release method allows for high aspect ratio, even 100 μm deep and successful release of overhanging structures, unlike conventional peeling. The ALD titania conformally covers the 3D multihierarchical structures of the template and protects the polymer during the release etch. Afterwards it prevents the high aspect ratio nanostructures from elasticity based collapse. The resulting nanostructured hybrid PDMS/titania replicas display robust superhydrophobicity without any further fluoro-coating or modification. Their mechanical and thermal robustness results from a thick nanostructured elastomeric layer which is conformally covered by ceramic titania instead of a monolayer hydrophobic coating. We have demonstrated the durability of these replicas against mechanical abrasion, knife scratches, rubbing, bending, peel tape test, high temperature annealing, UV exposure, water jet impingement and long term underwater storage. Though the material loses its superhydrophobicity in oxygen plasma exposure, a fast recovery from superhydrophilic to superhydrophobic can be achieved after 20 min UV irradiation. UV-assisted recovery is correlated with the high photoactivity of ALD titania film. This novel hybrid material will be applicable to the large area superhydrophobic surfaces in practical outdoor applications.

22 November 2017 in Scientific Reports
Verified
Journal Article
Open access
PDF file
SHSasha Hoshian
Sasha Hoshian
EKEsko Kankuri
Esko Kankuri
RRRobin H. A. Ras
Robin H. A. Ras
SFSami Franssila
Sami Franssila
VJVille Jokinen
Ville Jokinen
A top-down scalable method to produce flexible water and blood repellent tubes is introduced. The method is based on replication of overhanging nanostructures from an aluminum tube template to polydimethylsiloxane (PDMS) via atomic layer deposition (ALD) assisted sacrificial etching. The nanostructured PDMS/titania tubes are superhydrophobic with water contact angles 163 ± 1° (advancing) and 157 ± 1° (receding) without any further coating. Droplets are able to slide through a 4 mm (inner diameter) tube with low sliding angles of less than 10° for a 35 µL droplet. The superhydrophobic tube shows up to 5,000 times increase in acceleration of a sliding droplet compared to a control tube depending on the inclination angle. Compared to a free falling droplet, the superhydrophobic tube reduced the acceleration by only 38.55%, as compared to a 99.99% reduction for a control tube. The superhydrophobic tubes are blood repellent. Blood droplets (35 µL) roll through the tubes at 15° sliding angles without leaving a bloodstain. The tube surface is resistant to adhesion of activated platelets unlike planar control titania and smooth PDMS surfaces.

8 July 2015 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
SHSasha Hoshian
Sasha Hoshian
VJVille Jokinen
Ville Jokinen
KHKlas Hjort
Klas Hjort
RRRobin H. A. Ras
Robin H. A. Ras
SFSami Franssila
Sami Franssila

8 December 2016 in Micromachines
Verified
Journal Article
Open access
PDF file
SHSasha Hoshian
Sasha Hoshian
CGCristina Gaspar
Cristina Gaspar
TVTeemu Vasara
Teemu Vasara
FJFarzin Jahangiri
Farzin Jahangiri
VJVille Jokinen
Ville Jokinen
SFSami Franssila
Sami Franssila
We introduce a non-lithographical and vacuum-free method to pattern silicon. The method combines inkjet printing and metal assisted chemical etching (MaCE); we call this method “INKMAC”. A commercial silver ink is printed on top of a silicon surface to create the catalytic patterns for MaCE. The MaCE process leaves behind a set of silicon nanowires in the shape of the inkjet printed micrometer scale pattern. We further show how a potassium hydroxide (KOH) wet etching process can be used to rapidly etch away the nanowires, producing fully opened cavities and channels in the shape of the original printed pattern. We show how the printed lines (width 50–100 µm) can be etched into functional silicon microfluidic channels with different depths (10–40 µm) with aspect ratios close to one. We also used individual droplets (minimum diameter 30 µm) to produce cavities with a depth of 60 µm and an aspect ratio of two. Further, we discuss using the structured silicon substrate as a template for polymer replication to produce superhydrophobic surfaces.

18 September 2017 in European Journal of Oral Sciences
Verified
Journal Article
Closed access
PDF file
JLJarmo Leppäniemi
Jarmo Leppäniemi
SHSasha Hoshian
Sasha Hoshian
KSKimmo Suomalainen
Kimmo Suomalainen
TLToni Luoto
Toni Luoto
VJVille Jokinen
Ville Jokinen
JKJari Koskinen
Jari Koskinen