Jingwei Liu

Dr. Jingwei Liu

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 April 2022 in Polymers
Verified
Journal Article
Open access
PDF file
BDBing Du
Bing Du
ZLZhengxuan Li
Zhengxuan Li
HBHuimin Bai
Huimin Bai
QLQian Li
Qian Li
CZChangqi Zheng
Changqi Zheng
Liming ChenLiming Chen
Liming Chen
Long Fiber Reinforced Thermoplastic (LFT) is a lightweight, high-strength, and easy-to-recycle new vehicle composite material, and has good mechanical properties, heat resistance, and weather resistance, which has found increasing application in automobile industry. It is of importance to understand the relationship between micro phase, macro-mechanical properties and the structural performance of automobile components. This article evaluates the performance of LFT from the level of material to automobile components. The mechanical properties of LFT were numerically and theoretically predicted to provide instruction for the next material choice. Two typical structural components, namely, car seat frame and bumper beam, were selected to evaluate the performance of LGF/PP compared with other competing materials in terms of mechanical properties and cost. In the case of the same volume, the seat frame of 40% LECT/PP composite material is lighter and cheaper, which is conducive to energy saving and emission reduction. It was shown that the 40% LECT/PA66 car bumper beam had a higher energy absorption ratio, lighter weight, higher specific energy absorption, and advantageous material cost. LFT is a promising candidate for existing automobile components with its performance fulfilling the requirements.

9 October 2023 in Materials
Verified
Journal Article
Open access
PDF file
Jingwei LiuJingwei Liu
Jingwei Liu
STShenghui Tian
Shenghui Tian
JRJiaqi Ren
Jiaqi Ren
Jin HuangJin Huang
Jin Huang
LLLin Luo
Lin Luo
TZTianyong Zhang
Tianyong Zhang
Poor interlaminar fracture toughness has been a major issue in glass fiber-reinforced epoxy resin (GF/EP) laminate composites. In this paper, soft carboxy-terminated nitrile (CTBN) rubber particles and rigid nano-SiO2 are used to toughen the epoxy resin (EP) matrix to improve the interlayer properties of GF/EP laminate composites. The effects of adding two toughening agents on the mechanical and interlayer properties of GF/EP laminates were studied. The results showed that adding the two kinds of particles improved the mechanical properties of the epoxy matrix. When the additional amount of flexible CTBN rubber particles was 8 wt%, and the rigid nano-SiO2 was 0.5 wt%, the fracture toughness of the matrix resin was increased by 215.8%, and the tensile strength was only decreased by 2.3% compared with the pure epoxy resin. On this basis, the effects of two kinds of particles on the interlayer properties of GF/EP composites were studied. Compared with the unmodified GF/EP laminates, the interlayer shear strength and mode I interlayer fracture toughness is significantly improved by a toughening agent, and the energy release rate GIC of interlayer shear strength and interlayer fracture toughness is increased by 109.2%, and 86.8%, respectively. The flexible CTBN rubber particles and rigid nano-SiO2 improve the interfacial adhesion between GF and EP. The cavitation of the two particles and the plastic deformation of the matrix is the toughening mechanism of the interlayer properties of the composite. Such excellent interlaminar mechanical properties make it possible for GF/EP laminates to be widely used as engineering materials in various industries (e.g., aerospace, hydrogen energy, marine).

1 August 2022 in Polymers
Verified
Journal Article
Open access
PDF file
Jingwei LiuJingwei Liu
Jingwei Liu
YYYunsheng Ye
Yunsheng Ye
XXXiaolin Xie
Xiaolin Xie
XZXingping Zhou
Xingping Zhou
The dispersion level of carbon nanotubes (CNTs) and interface design are two of the most crucial roles in developing the superior mechanical performance of polymer/CNT nanocomposites. In this work, a series of azide-terminated poly(glycidyl methacrylate)-block-poly(hexyl methacrylate) (PGMA-b-PHMA) copolymers with different PHMA chain lengths and similar PGMA chain lengths were grafted on the surface of multiwall carbon nanotubes (MWNTs). PHMA length changes significantly impact the grafting density and solubility in organic solvents of as-prepared block copolymer functionalized MWNTs(bc@fMWNTs). Then, the bc@fMWNTs were introduced to epoxy, and the resulted epoxy/bc@fMWNT composites show better mechanical properties than neat epoxy and epoxy/p-MWNT composites. The results suggest that longer PHMA chains cause the two competitive and opposing effects on the dispersion state and soft interface. On the one hand, the longer PHMA chains on the surface of MWNTs would afford higher deformation for the matrix and enhanced mobility for MWNTs because of the soft and flexible nature of PHMA, enhancing the energy dissipation during strain. On the other hand, as the length of PHMA extends, the dispersion level of bc@fMWNTs in epoxy declines, which is harmful to the composite’s mechanical properties. Hence, epoxy/bc@fMWNTs composites with relatively short PHMA chains show the best tensile and fracture properties.

15 March 2024 in Polymers
Verified
Journal Article
Open access
PDF file
STShenghui Tian
Shenghui Tian
Jingwei LiuJingwei Liu
Jingwei Liu
JGJiabao Gu
Jiabao Gu
CXChaoting Xie
Chaoting Xie
XZXiong Zhang
Xiong Zhang
XLXinlu Liu
Xinlu Liu
Using alkali pretreatment can effectively remove residual variable-valence metals from non-metallic powder (WPCBP) in waste printed circuit boards. However, substantial amounts of waste lye are generated, which causes secondary pollution. On this basis, this study innovatively utilized waste alkali lye to prepare nano-magnesium hydroxide. When the dispersant polyethylene glycol 6000 was used at a dosage of 3 wt.% of the theoretical yield of magnesium hydroxide, the synthesized nano-magnesium hydroxide exhibited well-defined crystallinity, good thermal stability and uniform particle size distribution, with a median diameter of 197 nm. Furthermore, the in situ method was selected to prepare WPCBP/Mg(OH)2 hybrid filler (MW) and the combustion behavior, thermal and mechanical properties of PP blends filled with MW were evaluated. The combustion behavior of the PP/MW blends increased with the increasing hybrid ratio of Mg(OH)2, and the MW hybrid filler reinforced PP blends showed better thermal and mechanical properties compared to the PP/WPCBP blends. Furthermore, the dynamic mechanical properties of the PP/MW blends were also increased due to the improved interfacial adhesion between the MW fillers and PP matrix. This method demonstrated high economic and environmental value, providing a new direction for the high value-added utilization of WPCBP.

22 August 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
Jingwei LiuJingwei Liu
Jingwei Liu
STShenghui Tian
Shenghui Tian
JRJiaqi Ren
Jiaqi Ren
Jin HuangJin Huang
Jin Huang
LLLin Luo
Lin Luo
TZTianyong Zhang
Tianyong Zhang
Poor interlaminar fracture toughness has been a major issue in glass fiber-reinforced epoxy resin (GF/EP) laminate composites. In this paper, soft carboxy-terminated liquid nitrile (CTBN) rubber particles and rigid nano-SiO2 are used to toughen the epoxy resin (EP) matrix to improve the interlayer properties of GF/EP laminate composites. The effects of adding two toughening agents on the mechanical and interlayer properties of GF/EP laminates were studied. The results showed that adding the two kinds of particles improved the mechanical properties of the epoxy matrix. When the additional amount of flexible CTBN rubber particles was 8wt%, and the rigid nano SiO2 was 0.5wt%, the fracture toughness of the matrix resin was increased by 215.8%, and the tensile strength was only decreased by 2.3% compared with the pure epoxy resin. On this basis, the effects of two kinds of particles on the interlayer properties of GF/EP composites were studied. Compared with the unmodified GF/EP laminates, the interlayer shear strength and mode Ⅰ interlayer fracture toughness is significantly improved by toughening agent, and the energy release rate GIC of interlayer shear strength and interlayer fracture toughness is increased by 109.2%, and 86.8%, respectively.