Monitoring the defective multichip insulated gate bipolar transistor (IGBT) module is a cost-effective approach to improve the quality of customer service. A method using time duration of the gate charge is proposed to monitor bond wires fatigue of the multichip IGBT modules when the modules are in the off-state. It is based on the fact that failure of the chip branch due to bond wires fatigue changes the gate input capacitance of the multichip IGBT module. The health state of bond wires can be converted into the change of time duration of gate charge under the constant gate current. A driver containing the constant current source is proposed. The study results indicate that the time duration of the gate charge decreases significantly when the failure of the chip branch occurs, and the effect of junction temperature can be ignored within the special range of gate voltage. Condition monitoring can be implemented during the off-state of the multichip module and without considering the effects of junction temperature. The confirmatory experiment is carried out to verify the correctness of the proposed method.
14 November 2022 in IEEE Transactions on Power Electronics
A family of bipolar high step-up zeta–buck–boost converters based on the “coat circuit” is proposed, which can be used to connect a low-voltage dc source and a bipolar dc bus. Like the basic zeta or buck–boost converter, it contains only one active switch, so its control method and drive circuit are simple to achieve. The conversion ratio of the proposed converter is effectively increased through a “coat circuit,” and the voltage stress of the devices is reduced. In addition, the positive and negative voltages of the bipolar output voltage of the converter can be automatically equalized. Working principle and performance analysis of the proposed converter has been given in this article in detail, and a 400 W experimental prototype has been built to verify the correctness and effectiveness of the theoretical analysis.
11 January 2022 in IEEE Transactions on Power Electronics
Gate-oxide degradation has been one of the critical reliability concerns of silicon carbide (SiC) metal–oxide–semiconductor-field-effect transistors ( mosfet s), which could be monitored through aging-sensitive parameters. In this article, an online gate-oxide degradation monitoring method for planar SiC mosfet s is proposed by extracting gate charge time at a specific range of gate voltage . It is based on the findings that the input capacitances of planar SiC mosfet s change significantly over gate-oxide degradation, which is theoretically analyzed and experimentally verified. The capacitance variations are converted into the gate charge time as the new aging-sensitive parameter. The new parameter measurement circuit is proposed and integrated into the gate driver module. The article results indicate that the new parameter varies noticeably with gate-oxide degradation and the difference of this parameter caused by junction temperature is much smaller than that caused by degradation. Besides, the parameter is immune to package degradation and load current. The condition monitoring method can be implemented online since the parameter is extracted during the off -state of SiC mosfet devices, which does not affect normal operation. The confirmatory experiment is carried out to verify the correctness of the proposed method.
7 March 2025 in IEEE Transactions on Industrial Electronics
Aiming at the problem of interpolar voltage unbalance in bipolar low voltage dc (BLVDC) microgrid, a family of bipolar dc–dc converters with interpolar voltage self-balancing is proposed in this article. The proposed converters are composed of a full bridge inverter and four types of bipolar voltage multiplier (BVM) circuits. Benefiting from the characteristics of the proposed topology, its output power can automatically flow to the output side with lower voltage and has the ability to maintain the voltage balance between BLVDC buses. In addition, the proposed converters have ZVZCS soft-switching characteristics, and the control and driving circuits are consistent with the traditional full bridge inverter. The topology derivation, working principle, soft-switching and voltage self-balancing performances of the proposed converter are analyzed, and a 1 kW experimental prototype with its control system is designed. The experimental results verify the accuracy of the theory and analysis.
8 April 2025 in IEEE Transactions on Transportation Electrification
The bipolar dc power architecture provides a new high-efficiency and high-reliability solution. Maintaining interpolar voltage balance is crucial in bipolar structures to ensure the reliable and stable operation of the system. This article proposes a family of bipolar dc-dc converters based on bipolar voltage multipliers (BVMs). Notably, the proposed BVM structure has the capacity to autonomously achieve interpolar voltage balance without external balance control strategy. This inherent feature significantly alleviates control circuit complexity. Meanwhile, the BVM structure possesses rectification functionality, facilitating its connection to various front-stage structures with ac output. This article provides a detailed exposition of the operational principles and performance analysis of the proposed voltage balancers (VBs) and discusses a 1-kW prototype experiment. The experimental results validate the accuracy of the theoretical analysis.
12 February 2020 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Monitoring the defective insulated gate bipolar transistor (IGBT) module is a cost-effective approach to improve the quality of customer service. In general, the parasitic parameters of bond wires inside the IGBT module are affected by aging. Module transconductance reflects the characteristics of the IGBT module and contains information about bond wire health status. It is investigated as a precursor parameter to monitor the bond wire defects in this article. The mathematical model of module transconductance is deduced to establish the relationship between module transconductance and the parameter of bond wires, which indicates that the module transconductance decreases with the increase of bond wire defects. For accurate and safe measurement, the influence of temperature difference caused by bond wire defects during measurement and safety measurement area where the module operates in the active region are discussed. Based on the safety measurement area and the method to eliminate the difference in temperature, a pulse ramp drive circuit is proposed to extract module transconductance. The simulation and experiments are carried out to validate the feasibility of the measurement method and correctness of the theoretical analysis.