Biomechanical factors influence stress in the aortic wall. The aim of this study was to assess how the diameter and shape of the vessel, blood pressure and longitudinal systolic aortic stretching (SAS) caused by the contraction of the myocardium influence stress in the aortic wall. Three computational models of the non-dilated aorta and aneurysms of the ascending aorta and aortic root were created. Then, finite elements analyses were carried out. The models were subjected to blood pressure (120 mmHg and 160 mmHg) and longitudinal systolic aortic stretching (0 mm, 5 mm, 10 mm and 15 mm). The influence of wall elasticity was examined too. Blood pressure had a smaller impact on the stress than the SAS. An increase in blood pressure from 120 mmHg to 160 mmHg increased the peak wall stress (PWS) on average by 0.1 MPa in all models. A 5 mm SAS caused a 0.1–0.2 MPa increase in PWS in all the models. The increase in PWS caused by a 10 mm and 15 mm SAS was 0.2 MPa and 0.4 MPa in the non-dilated aorta, 0.2–0.3 MPa and 0.3–0.5 MPa in the aneurysm of the ascending aorta, and 0.1–0.2 MPa and 0.2–0.3 MPa in the aortic root aneurysm model, respectively. The loss of elasticity of the aneurysmal wall resulted in an increase of PWS by 0.1–0.2 MPa. Aortic geometry, wall stiffness, blood pressure and SAS have an impact on PWS. However, SAS had the biggest impact on wall stress. The results of this study may be useful in future patient-specific computational models used to assess the risk of aortic complications.

The risk of aortic dissection should be assessed based not only on the aortic diameter, but also on other biomechanical parameters that have an impact on the stress in the aortic wall. This study evaluates very rare clinical scenarios of patients with both pre- and post-dissection computed tomography (CT) images and evaluates whether an increased wall stress correlates with the localization of an intimal entry tear in Type A aortic dissection. CT-angiography images of 4 patients performed shortly prior to and after developing Type A aortic dissection were evaluated. The stress distribution in the pre-dissection aortas was evaluated using the finite elements method. Then, the areas of high stress in the pre-dissection aortas were compared to the localization of the intimal entry tears in the dissected vessels. In all the patients, the pre-dissection areas of high wall stress correlated with the location of the intimal tears. The highest stress was not observed in the most dilated segments of the aorta but was predominantly found in the areas of an abrupt change in the geometry of the aorta. Wall stress can indicate the areas susceptible to the formation of an intimal tear and subsequent aortic dissection. Stress analysis may be a valuable tool to predict the risk of aortic dissection in patients with aortic dilatation.

The research focussed on analysing structural and mechanical properties in the intervertebral disc (IVD), caused by long-term cyclic loading. Spinal motion segments were divided into two groups: the control (C), and the group in which it was analysed the impact of posterior column in the load-bearing system of the spine—specimens with intact posterior column (IPC) and without posterior column (WPC). To evaluate the structural and mechanical changes, the specimens were tested with simulation of 100,000 compression-flexion load cycles after which it was performed macroscopic analysis. Mechanical properties of the annulus fibrosis (AF) from the anterior and posterior regions of the IVD were tested at the uniaxial tension test. The stiffness coefficient values were statistically 32% higher in the WPC group (110 N/mm) than in the IPC (79 N/mm). The dynamics of increase in this parameter does not correspond with the course of decrease in height loss. WPC segments revealed clear structural changes that mainly involve the posterior regions of the IVD (bulging and delamination with the effect of separation of collagen fibre bundles). Pathological changes also caused decreases in the value of stress in the AF. The greatest changes in the stress value about group C (7.43 ± 4.49 MPa) were observed in the front part of the fibrous ring, where this value was for IPC 4.49 ± 4.78 MPa and WPC 2.56 ± 1.01 MPa. The research indicates that the applied load model allows simulating damage that occurs in pathological IVD. And the posterior column’s presence affects this change’s dynamics, structural and mechanical properties of AF.