Mitsuru Ohata

Prof. Mitsuru Ohata

Osaka University, Ōsaka, Japan

Research Focus & Metrics

Academic Career Length

36Years (1991-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 January 2004 in Science and Technology of Advanced Materials
Verified
Journal Article
Open access
MOMitsuru Ohata
Mitsuru Ohata
MTMasao Toyoda
Masao Toyoda
Evaluation of ductile crack initiation in steel welded structures subjected to seismic loading is crucial for structural design or safety assessment to prevent brittle fracture induced by ductile cracking. Observation of ductile crack initiation behavior of round-bar specimens with/without circumferential notches tested in single tension revealed that the main controlling factor for ductile cracking in the employed two-phase steel is not growth of voids induced by large inclusions, but nucleation of micro-voids in a soft phase (Ferrite phase) near the Ferrite–Pearlite interface after large-scale plastic straining. The material damage concept under reverse loading, which correlates the material damage for micro-void nucleation to macro-scale mechanical parameters, was proposed in consideration of two aspects of the Bauschinger effect: (a) a mechanical aspect which influences deformation and stress/strain behaviors in steel structures, (b) a material damage aspect caused by dislocation behavior. A new criterion for ductile cracking of structural members under cyclic loading was proposed on the basis of the proposed effective damage concept and ‘two-parameter criterion,’ which can be applied to the steel structures under increasing load in a single direction. The validity of the advanced two-parameter criterion was verified by subjecting round-bar specimens to cyclic loading tests along the axial direction and cross-shaped specimens to cyclic 3-point bending tests. Consequently, the advanced two-parameter ductile cracking criterion was found to be a transferable criterion for evaluation of critical loading cycle of structural members from small-scale tensile test results.

23 April 2009 in International Journal of Damage Mechanics
Verified
Journal Article
Closed access
MOMitsuru Ohata
Mitsuru Ohata
TFTakuya Fukahori
Takuya Fukahori
FMFumiyoshi Minami
Fumiyoshi Minami
This study pays attention to reveal material properties that control a resistance curve for ductile crack growth (CTOD-R curve) on the basis of the mechanism for ductile crack growth, so that the R-curve could be numerically predicted only from those properties. Crack growth tests using 3-point bend specimens with a fatigue pre-crack are conducted for two steels that have different ductile crack growth resistance, whereas both steels have the same mechanical properties in terms of strength and work hardening. Observation of crack growth behaviors provides that different mechanisms between ductile crack initiation from fatigue pre-crack and subsequent growth process can be applied. It is shown that two types of ductile properties of steel associated with ductile damage can mainly influence CTOD-R curve; one is a resistance of ductile crack initiation estimated with critical local strain for ductile cracking from a surface of notch root, and the other one is a stress triaxiality dependent ductility obtained with circumferentially notched round-bar specimens. The damage model for numerically simulating the R-curve is proposed taking the above two ductile properties into account, where the ductile crack initiation from crack-tip is in accordance with local strain criterion, and the subsequent crack growth triaxiality dependent damage criterion. The proposed model accurately predicts the measured different R-curves between two steels used that have the same ‘strength properties’, and also the stress triaxiality dependence of R-curve.

1 January 2003 in QUARTERLY JOURNAL OF THE JAPAN WELDING SOCIETY
Verified
Journal Article
Closed access
PDF file
TSTatsuya Shintomi
Tatsuya Shintomi
ICIchiro Chikushi
Ichiro Chikushi
YHYoshikazu Hashimoto
Yoshikazu Hashimoto
MOMitsuru Ohata
Mitsuru Ohata
MMMasahito Mochizuki
Masahito Mochizuki
MTMasao Toyoda
Masao Toyoda
It has been greatly interested that the development of a new high strength steel with grain refinement. Fine grain steel has the same component and the weldability as a mild steel, whereas conventional high strength steel has a low weldability due to its alloying elements. It is found the occurrence of softening caused by coarsening in the heat-affected-zone (HAZ) of weld parts of the fine grain steels and mechanical design of weld parts including weld HAZ softening becomes much important. In this paper, the production of an ultra-fine grain steel (NFG steel) produced by high reduction and high cooling rate is firstly introduced. Mechanical properties of the weld part is examined by considering the characteristics of tensile strength under the theory of the strength of the undermatched joints. The effects of the mechanical and geometrical heterogeneity on tensile strength of the HAZ softening joint are studied by using the large-deformation finite-element analysis. It is found that a design of the HAZ softening joint is possible considering welding conditions and tensile strength of the joint mostly overreach that of the base metal.

1 July 2010 in Welding in the World
Verified
Journal Article
Closed access
PDF file
TTTetsuya Tagawa
Tetsuya Tagawa
YKYoichi Kayamori
Yoichi Kayamori
MOMitsuru Ohata
Mitsuru Ohata
YYYoichi Yamashita
Yoichi Yamashita
THTsunehisa Handa
Tsunehisa Handa
YHYukito Hagihara
Yukito Hagihara

8 July 2015 in Welding in the World
Verified
Journal Article
Closed access
PDF file
MOMitsuru Ohata
Mitsuru Ohata
GMG. Morimoto
G. Morimoto
YFY. Fukuda
Y. Fukuda
FMF. Minami
F. Minami
KIK. Inose
K. Inose
THT. Handa
T. Handa

1 January 1996 in Journal of the Society of Materials Science, Japan
Verified
Journal Article
Open access
PDF file
FMFumiyoshi Minami
Fumiyoshi Minami
CRClaudio Ruggieri
Claudio Ruggieri
MOMitsuru Ohata
Mitsuru Ohata
MTMasao Toyoda
Masao Toyoda
The effects of specimen geometry and loading mode on the resistance to brittle fracture initiation were analyzed by the local approach. The fracture resistance of materials under a large scale yielding condition evaluated by the conventional fracture mechanics parameters, such as crack tip opening displacement (CTOD), depends to a large extent on the specimen geometry and loading mode. This is due to the geometrical constraint effect on the crack tip stress field. The three-dimensional FE analysis figured out that, as plasticity developed, a shallow notch bend specimen and tension specimens (CCP and DECP) showed significant loss of constraint compared to a deep notch bend specimen. This led to a lower stress near the crack tip for the shallow notch bend specimen and tension specimens than the deep notch bend specimen. By contrast, the critical Weibull stress at brittle fracture according to the local approach did not depend on the geometry of specimens used. This paper demonstrates the independence of the critical Weibull stress on the crack depth of 3-point bend specimen. As an advantage, the local approach enabled us to predict the specimen geometry effect on the critical CTOD at fracture.The effects of specimen geometry and loading mode on the critical CTOD at fracture depend on the hardenability of materials. In the case of high hardening materials, the critical CTOD is not very sensitive to the specimen geometry and loading mode excepting the thickness effect on the critical CTOD for materials with a large scatter in toughness. On the other hand, for low hardening materials, the critical CTOD is affected to a large extent by the crack depth and loading mode of specimens.