Yuzheng Li

Mr. Yuzheng Li

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 June 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YLYuzheng Li
Yuzheng Li
JDJintao Du
Jintao Du
YLYijun Lan
Yijun Lan
HDHeng Du
Heng Du
HHHui Huang
Hui Huang
Aiming at the problem of valve port erosion caused by contaminated particles, a three-dimensional prediction model of valve orifice erosion was established based on computational fluid dynamics (CFD) and erosion theory, considering the influence of the valve port eddy current on the oil flow. The discrete phase model (DPM) of fluent is used to obtain the orifice erosion location and erosion rate, and the causes of erosion of the high-speed on/off valve are analyzed. On this basis, several factors influencing valve port erosion are simulated to investigate the relationship between particle collision behavior and valve port erosion morphology under different factors, and the change rule of valve port erosion under different factors is analyzed. The results show that the high-speed on/off valve service life decreases with a larger cone angle of the spool, a larger pressure difference at the valve port, a larger proportion of large particle contaminants in the oil, a higher oil contamination level, and a larger filter aperture. In addition, the grey relational analysis method is used to clarify the pressure difference at the valve port, the particle size, and the filter aperture as the three most important factors affecting the erosion of the valve port of a high-speed on/off valve.

17 September 2024 in Measurement
Verified
Journal Article
Closed access
PCPeiyang Chen
Peiyang Chen
YLYuzheng Li
Yuzheng Li
HGHao Gao
Hao Gao
XZXiaolong Zhang
Xiaolong Zhang
HDHeng Du
Heng Du
TRTianyu Ren
Tianyu Ren

16 December 2021 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Verified
Journal Article
Closed access
PDF file
ZZZhizhong Zhang
Zhizhong Zhang
HDHeng Du
Heng Du
SCShumei Chen
Shumei Chen
YLYuzheng Li
Yuzheng Li
HWHan wang
Han wang
Ackermann steering is important for the steering performance of heavy multi-axle vehicle. When Ackermann steering condition is not satisfied, it will lead to abnormal tire wear. Traditional trapezoidal mechanism of heavy multi-axle vehicle is a single degree of freedom (DOF) mechanism, which is difficult to completely realize Ackermann steering. In this paper, a new two DOF electro-hydraulic servo steering system (TDEHSSS) by using a variable length tie rod is proposed for solving the issue. First, a complex nonlinear dynamic model of TDEHSSS is established. This model includes the two DOF mechanical model based on a Lagrange equation, the valve-controlled double steering power cylinders model and the valve-controlled tie rod cylinder model. Then, a simulation model is built through MATLAB/Simulink and the simulation results show that TDEHSSS can realize the proposed requirement. At last, a test bench is founded to verify model. It is indicated that the simulation and experimental curves are consistent, showing that mathematical model is in accordance with the experimental system. This research is valuable for analyzing TDEHSSS, designing advanced controllers, and finally realizing Ackermann steering for heavy multi-axle vehicles.

17 September 2025 in Advances in Mechanical Engineering
Verified
Journal Article
Open access
FCFulong Chen
Fulong Chen
YLYuzheng Li
Yuzheng Li
FLFuqi Li
Fuqi Li
HDHeng Du
Heng Du
HHHui Huang
Hui Huang
KXKaiyi Xie
Kaiyi Xie
It is found through experiments that the amplitude, waveform and periodicity of the water hammer pressure pulsation under the continuous on/off of the valve in the digital hydraulic system are affected by the frequency of the valve switching valve, which is greatly deviated from the prediction and evaluation results of the traditional water hammer model. Therefore, to improve the prediction accuracy of the pressure pulsation (water hammer) model in continuous switching digital hydraulic systems, this work starts from the fundamental water hammer mechanism. Based on the on/off characteristics of the high-speed switching valve, a relationship is established between the valve opening variation and the valve switching frequency through a time-dependent function. Furthermore, by accounting for the elasticity of the pipe walls and the compressibility of the fluid, a novel model capable of predicting water hammer pressure pulsations under continuous valve switching is constructed. The accuracy of this new model was experimentally verified, demonstrating a prediction error for the system’s water hammer pressure that does not exceed 5%. This research model provides theoretical support for the reliability design of high-speed switch valve hydraulic systems by accurately predicting the water hammer pressure of the system under continuous on/off, and is also of great significance for further in-depth research on digital hydraulic valve systems.

24 May 2024 in Journal of Vibration and Control
Verified
Journal Article
Closed access
HHHui Huang
Hui Huang
XYXin Yang
Xin Yang
BMBaizhou Ma
Baizhou Ma
LXLanfang Xiao
Lanfang Xiao
SCShumei Chen
Shumei Chen
XLXiufang Lin
Xiufang Lin
When hydraulic-legged robots move under high loads on irregular ground, they are vulnerable to ground impacts. Vibration affects the motion performance of the robot and damages its mechanical structure. This study aims to improve the properties of vibration absorption and impact resistance of hydraulic-legged robots. Because the traditional MR damper (MRD) has small output in finite volume, a novel MRD with a multistage flow channel (MFC-MRD) can output a large damping force designed. First, an MRD prototype was designed for a mechanical leg’s driving joint. Subsequently, the system is analyzed theoretically, and a semi-active control strategy is designed and simulated. Finally, the vibration and impact resistance of the prototype were tested. The experimental results show that in the signal tracking experiment, the maximum overshoot under semi-active control was reduced by 53.0%, and the settling time was reduced by 76.9% compared with the passive control. The impact test reduced the maximum displacement fluctuation by 41.09%, and the buffer time is only 0.24 s.

29 July 2025 in Measurement
Verified
Journal Article
Closed access
FCFulong Chen
Fulong Chen
HHHui Huang
Hui Huang
YLYuzheng Li
Yuzheng Li
GSGuolei Si
Guolei Si
JSJunshou Su
Junshou Su
FLFuqi Li
Fuqi Li