Bond wire damage is one of the most common failure modes of metal-oxide semiconductor field-effect transistor (MOSFET) power devices in wire-welded packaging. This paper proposes a novel bond wire damage detection approach based on two-port network measurement by identifying the MOSFET source parasitic inductance (LS). Numerical calculation shows that the number of bond wire liftoffs will change the LS, which can be used as an effective bond wire damage precursor. Considering a power MOSFET as a two-port network, LS is accurately extracted from frequency domain impedance (Z−parameter) using a vector network analyzer under zero biasing conditions. Bond wire cutoff experiments are employed to validate the proposed approach for bond wire damage detection. The result shows that LS increases with the rising severity of bond wire faults, and even the slight fault shows a high sensitivity, which can be effectively used to quantify the number of bond wire liftoffs of discrete MOSFETs. Meanwhile, the source parasitic resistance (RS) extracted from the proposed two-port network measurement can be used for the bond wire damage detection of high switching frequency silicon carbide MOSFETs. This approach offers an effective quality screening technology for discrete MOSFETs without power on treatment.
8 February 2024 in IEEE Transactions on Device and Materials Reliability
Metal-oxide-semiconductor field-effect transistors (MOSFETs) undergo fatigue degradation under high thermal and electrical stresses. This process results in changes in their parasitic parameters, which can be detected using frequency domain reflectometry (FDR). Frequency domain impedance analysis is employed to characterize the various quality states of Si and SiC MOSFETs obtained from accelerated aging experiments. Results demonstrate a consistent increase in parasitic resistance as the devices degrade. By determining the drain-source parasitic resistance at the self-resonant frequency (fSRF) and the drain-source on-resistance for MOSFETs with varying degradation degrees, positive linear numerical fitting equations (14)-(15) are established to predict MOSFET degradation under zero DC bias voltage. In addition, FDR technology is used to identify the drain parasitic resistance at the fSRF of MOSFET samples with different sizes of defects in the sintered silver layer. These results reveal a positive correlation between the quality of the sintered silver layer and RDSRF. The proposed approach is an effective quality screening technology for power semiconductor devices without requiring power-on treatment.
1 December 2023 in IEEE Transactions on Instrumentation and Measurement
Although the problem of pad cratering has become the focus of PCB manufacturing industry for nearly a decade, the existing test method and equipment have not been widely promoted in industrial usage. This approach is unsuitable for large-scale industrial application because the existing equipment and consumables are expensive, the test success rate is low, and the test procedure requires human operation. In this study, a pin pull test method is proposed; it implements highly stable soldering between the pull pin and the target pad through the optimized pins and soldering method, thereby greatly improving the pulling success rate and obtaining ideal adaptability for micro-pads with diameter below 0.5 mm. In addition, the pull pin can be repeatedly used, effectively reducing testing costs. A stable control of the solder ball size without human intervention can be achieved with the unique solder ball generating method. The key parameters, such as the peak soldering temperature, pulling speed, and the matching relationship between pull pin and target pads, are studied in the experiment. The success rates of the test for 0.3 and 0.5 mm pads are validated, and results indicate that the test stability on pad soldering and pulling is remarkably improved.
With the development of portable electronic equipment, the power density and volume of power adapters have attracted more and more attention. Using high-frequency switching elements to reduce the volume of inductive elements, PFC circuit to improve the power factor and reduce the volume of capacitive elements, using highly integrated elements is a common method. When using high-frequency switching elements, the power integrity, signal integrity, and impedance matching of high-frequency signal lines should be considered. The design of power management SOC faces the disadvantages of the long development cycle and high investment cost.This paper presents a system packaging scheme, which encapsulates the key components of PFC and LLC step-down circuits, rectifier soft bridge, and two-stage step-down circuit [1]. The module realizes the functions of 150V-250V DC wide voltage input, 20V and 5V DC output. The package interconnection model is established and imported into ANSYS software for simulation. The power integrity of the power supply network is analyzed, the planar resonance point of the power supply is explored, and the decoupling optimization is carried out [2]. Through simulation analysis, the layout of power and signal wiring is optimized. Through optimization design, the module achieves the maximum voltage drop of 5V within 5%, and the PDN meets the impedance requirements within the target frequency, meeting the design requirements. The miniaturization and integration of modules can be realized by system-level packaging of DC-DC circuits. The results show that the scheme is advanced and feasible.