Quanli Zhang

Dr. Quanli Zhang

College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 March 2024 in Applied Surface Science
Verified
Journal Article
Closed access
JLJian Liu
Jian Liu
MWMingtao Wu
Mingtao Wu
ZSZhiyuan Sun
Zhiyuan Sun
Quanli ZhangQuanli Zhang
Quanli Zhang
YZYandan Zhu
Yandan Zhu
YFYucan Fu
Yucan Fu

1 February 2016 in Materials & Design
Verified
Journal Article
Open access
Quanli ZhangQuanli Zhang
Quanli Zhang
STSuet To
Suet To
Qingliang ZhaoQingliang Zhao
Qingliang Zhao
Bing GuoBing Guo
Bing Guo
The surface damage mechanisms of WC/Co and Reaction-bonded SiC/Si (RB-SiC/Si) composites under high spindle speed grinding (HSSG) were investigated in the present work. Sharp edge loss and grit splintering were identified as two typical diamond wheel wear mechanisms. Plastic scratching grooves, Co extrusion and WC dislodgement were generated on the machined surface of WC/Co after grinding, while micro-pits of varied sizes at the phase boundaries and plastic scratching grooves were the main surface characteristics for RB-SiC/Si. Moreover, it was found that non-uniform surface finish at different radial positions resulted from the increase in material removal rate for both WC/Co and RB-SiC/Si, and the simulated results based on Soneys' model mostly corresponded with the measured outcomes. In addition, obvious relative wheel-workpiece vibration induced surface waviness was found, and its effect on the surface profile was analyzed for the wheel edge profile considered, which differed with that from single point diamond machining (SPDT).Department of Industrial and Systems Engineerin

29 August 2019 in Micromachines
Verified
Journal Article
Open access
PDF file
Quanli ZhangQuanli Zhang
Quanli Zhang
GNguo nan
guo nan
YCYan Chen
Yan Chen
YFYucan Fu
Yucan Fu
QZQingliang Zhao
Qingliang Zhao
The surface generation mechanism of the Cu alloys in ultra-precision diamond turning is investigated by both simulation and experimental methods, where the effects of the cutting parameters on the surface characteristics are explored, including the workpiece spindle speed, the cutting depth, the feed rate and the nose radius of the diamond tool. To verify the built model, the cutting experiments are conducted at selected parameters, where the causes of the error between the simulation and the machining results are analyzed, including the effects of the materials microstructure and the diamond tool wear. In addition, the nanometric surface characteristics of the Cu alloys after the diamond turning are identified, including the finer scratching grooves caused by the tool wear, the formation of the surface burs and the adhesion of graphite. The results show that the built model can be basically used to predict the surface topography for the selection of the appropriate machining parameters in the ultra-precision diamond turning process.

2 September 2024 in Applied Surface Science
Verified
Journal Article
Closed access
CDCanwen Dai
Canwen Dai
Quanli ZhangQuanli Zhang
Quanli Zhang
JWJingwei Wang
Jingwei Wang
JRJiaqi Ran
Jiaqi Ran
Zejia ZhaoZejia Zhao
Zejia Zhao

5 September 2021 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
WWWentao Wang
Wentao Wang
Quanli ZhangQuanli Zhang
Quanli Zhang
CCChenglong Chu
Chenglong Chu
ZZZhen Zhang
Zhen Zhang
JXJiuhua Xu
Jiuhua Xu

1 October 2018
Verified
Conference Paper
Closed access
ZLZhixiong Li
Zhixiong Li
Quanli ZhangQuanli Zhang
Quanli Zhang
HLHuaidong Luo
Huaidong Luo
HWHongwei Wang
Hongwei Wang
JWJin Wang
Jin Wang
LZLibing Zhou
Libing Zhou
Downhole electric drilling, with a motor driving the drill bit to rotate, has been an emerging trend for oil/gas drilling industry. This paper proposes an effective starting strategy for permanent magnet synchronous motors with step-up transformer, sin-wave filter and long cables for the downhole electric drilling applications. Due to the saturation effect of the transformer in low frequency region, the traditional sensorless vector control and open V/f control may fail during the startup process of the motor. The proposed starting strategy is based on a modified I-f velocity open loop control, which supplies sufficient starting torque, and the saturation effect of the transformer is effectively mitigated. A filter capacitance current compensation method is proposed to modify the inverter current references. The frequency stablization loop independent on the changeful system parameters is designed to provide stability control to mitigate speed oscillatory or motor stoppage. Finally, the feasibility and effectiveness of the proposed control strategy is verified through simulation results with Matlab/Simulink.