Hongqiang Liao

Mr. Hongqiang Liao


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

1 September 2021 in Construction and Building Materials
Verified
Journal Article
Closed access
ZMZhuohui Ma
Zhuohui Ma
HLHongqiang Liao
Hongqiang Liao
LWLi Wang
Li Wang
FCFangqin Cheng
Fangqin Cheng

2 January 2023 in Composites Science and Technology
Verified
Journal Article
Closed access
CLChao Li
Chao Li
HLHongqiang Liao
Hongqiang Liao
HGHongyu Gao
Hongyu Gao
Huirong ZhangHuirong Zhang
Huirong Zhang
FCFangqin Cheng
Fangqin Cheng

11 January 2023 in Materials
Verified
Journal Article
Open access
PDF file
JWJianfang Wu
Jianfang Wu
HLHongqiang Liao
Hongqiang Liao
ZMZhuohui Ma
Zhuohui Ma
HSHuiping Song
Huiping Song
FCFangqin Cheng
Fangqin Cheng
To better understand the pozzolanic activity in fly ash used as a supplementary cementitious material in cement or concrete, calcium silicate hydrate (C-S-H) has been synthesized by adding silica fume to a supersaturated calcium hydroxide solution prepared by mixing calcium oxide and ultrapure water. Thermogravimetric analysis results have revealed the variation in the weight loss due to C-S-H in the samples and the conversion ratio of calcium oxide (the μCaO value), which represents the proportion of calcium oxide in the initial reaction mixture used to produce C-S-H, with curing time. The weight loss due to C-S-H and the μCaO value were both maximized (13.5% and 90.4%, respectively) when the initial C/S molar ratio was 1.0 and the curing time was 90 d. X-ray diffraction (XRD) analysis has indicated that C-S-H in the samples after curing for 7 d had the composition Ca1.5SiO3.5·xH2O. 29Si magic angle spinning (MAS) nuclear magnetic resonance (NMR) analysis has revealed that the degree of polymerization of C-S-H increased with an increase in curing time for samples with an initial C/S molar ratio of 1.0. The ratio of internal to terminal tetrahedra (Q2/Q1) increased from 2.29 to 4.28 with the increase in curing time from 7 d to 90 d. At curing times ≥ 28 d, a leaf-like C-S-H structure was observed by scanning electron microscopy (SEM). An ectopic nucleation–polymerization reaction process is proposed for the formation mechanism of C-S-H.

24 May 2024 in ACS Sustainable Chemistry & Engineering
Verified
Journal Article
Closed access
SYShizhao Yang
Shizhao Yang
XWXujiang Wang
Xujiang Wang
JLJingwei Li
Jingwei Li
XYXingliang Yao
Xingliang Yao
RMRenjie Mi
Renjie Mi
WWwenlong Wang
wenlong Wang

9 June 2022 in ACS Omega
Verified
Journal Article
Open access
ZMZhuohui Ma
Zhuohui Ma
HLHongqiang Liao
Hongqiang Liao
ZPZihe Pan
Zihe Pan
FCFangqin Cheng
Fangqin Cheng
Steel slag is a calcium-containing alkaline industrial solid waste that can replace limestone for flue gas desulfurization. It can remove SO2 and coproduce silica gel while avoiding CO2 emission from limestone in the desulfurization process. In this study, steel slag with a D 50 of 3.15 μm was used to remove SO2. At room temperature, with a solid-liquid ratio of 1:10, a stirring speed of 800 rpm, and the mixed gas introduced at a flow rate of 0.8 mL/min, 1 ton of steel slag could remove 406.7 kg of SO2, a SO2 removal efficiency typical of existing calcium-rich desulfurizers. As limestone desulfurization can release CO2, when limestone desulfurization was replaced with steel slag of equal desulfurization ratio, CO2 emissions could be reduced by 279.6 kg and limestone could be reduced by 635.5 kg. The yield of silica gel was 5.1%. Silica gel pore structure parameters were close to those of commercially available B silica gel. Products after desulfurization were mainly CaSO4 ·2H2O, CaSO4 ·0.5H2O, CaSO3 ·0.5H2O, and silica gel. With a silica gel dosage of 30 mg, a temperature of 20 °C, a pH value of 6.00, a stirring time of 0.5 h, and a methylene blue concentration of 0.020 mg/mL, the removal ratio of methylene blue adsorbed by silica gel was 98.4%.