Zhiqiang Zhang

Dr. Zhiqiang Zhang

Civil Aviation University of China, Tianjin, China

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 August 2024 in International Journal of Mechanical Sciences
Verified
Journal Article
Closed access
QGQingze Gou
Qingze Gou
ZZZhiqiang Zhang
Zhiqiang Zhang
LXLianyong Xu
Lianyong Xu
DWDongquan Wu
Dongquan Wu
TZTiangang Zhang
Tiangang Zhang
HLHongli Liu
Hongli Liu

24 February 2025 in Tribology International
Verified
Journal Article
Closed access
ZZZhiqiang Zhang
Zhiqiang Zhang
XPXuhui Pei
Xuhui Pei
YDYin Du
Yin Du
ZYZiming Yu
Ziming Yu
XYXinyu Yao
Xinyu Yao
HWHaifeng Wang
Haifeng Wang

2 November 2024 in Optics & Laser Technology
Verified
Journal Article
Closed access
TZTiangang Zhang
Tiangang Zhang
TLTianxiang Liu
Tianxiang Liu
SZShu-Sen Zhao
Shu-Sen Zhao
ZZZhiqiang Zhang
Zhiqiang Zhang
YLYanan Liu
Yanan Liu
CZCuiying Zhong
Cuiying Zhong

27 June 2022 in Coatings
Verified
Journal Article
Open access
PDF file
ZZZhiqiang Zhang
Zhiqiang Zhang
QYQIan Yang
QIan Yang
FYFan Yang
Fan Yang
HZHongwei Zhang
Hongwei Zhang
TZTiangang Zhang
Tiangang Zhang
QMQiang Ma
Qiang Ma
Several innovative mixed powders of Ti6Al4V and NiCr-Cr3C2 with different CeO2 contents (0, 1, 2, 3, and 4 wt.%) were designed, and Ti2C-reinforced CrTi4-based composite coatings were prepared on the Ti6Al4V surface via laser cladding technology. The effects of CeO2 amount on the forming quality, microstructure, hardness, and wear resistance of the composite coatings were studied. The results showed that the CeO2 amount had a significant influence on the forming quality of the composite coatings. The cracks were eliminated completely when the CeO2 content was 2 wt.%; furthermore, the lowest porosity was obtained with the addition of 3 wt.% CeO2. The primary phase constituents of the coatings were non-stoichiometric Ti2C and a β-type solid solution (CrTi4) as the reinforcement and matrix, respectively. CeO2 and a low quantity of Ce2O3 were re-precipitated at the Ti2C/CrTi4 interface and CrTi4 grain boundary in the coatings with CeO2 addition. In addition, the average hardness of the composite coatings was 1.28–1.34 times higher than that of the Ti6Al4V substrate. The wear resistance of the composite coatings was significantly higher than that of the substrate. However, both the composite coatings and the Ti6Al4V substrate exhibited a mixed-wear mode, i.e., abrasive and adhesive wear.

4 October 2023 in Welding in the World
Verified
Journal Article
Closed access
PDF file
ZZZhiqiang Zhang
Zhiqiang Zhang
QGQingze Gou
Qingze Gou
TZTiangang Zhang
Tiangang Zhang
XLXuecheng Lu
Xuecheng Lu
LXLianyong Xu
Lianyong Xu
JZJing Zhang
Jing Zhang

8 January 2024 in Actuators
Verified
Journal Article
Open access
PDF file
SHShiwei He
Shiwei He
ZZZhiqiang Zhang
Zhiqiang Zhang
HLHanxi Li
Hanxi Li
TZTiangang Zhang
Tiangang Zhang
XLXuecheng Lu
Xuecheng Lu
JKJiajie Kang
Jiajie Kang
A thin-walled structure of high-strength aluminum alloy 2024 (AA2024) was fabricated using novel laser and cold metal transfer and pulse (CMT-P) arc hybrid additive manufacturing (LCAHAM) technology. The influence of the wire feeding speed, scanning speed, and laser power on the forming quality was systematically studied by the response surface methodology, probability statistical theory, and multi-objective optimization algorithm. The result showed that the forming accuracy was significantly more affected by the laser power than by the wire feeding speed and scanning speed. Specifically, there was an obvious correlation between the interaction of the laser power and wire feeding speed and the resulting formation accuracy of LCAHAM AA2024. Moreover, the laser power, wire feeding speed, and scanning speed all had noticeable effects on the spattering degree during the LCAHAM AA2024 process, with the influence of the laser power surpassing that of the other two factors. Importantly, these three factors demonstrated minimal mutual interaction on spattering. Furthermore, the scanning speed emerged as the most significant factor influencing porosity compared to the wire feeding speed and laser power. It was crucial to highlight that the combined effects of the wire feed speed and laser power played an obvious role in reducing porosity. Considering the forming accuracy, spattering degree, and porosity collectively, the recommended process parameters were as follows: a wire feeding speed ranging from 4.2 to 4.3 m/min, a scanning speed between 15 and 17 mm/s, and a laser power set at approximately 2000 W, where the forming accuracy was 84–85%, the spattering degree fell within 1.0–1.2%, and the porosity was 0.7–0.9%.