Iwona Dobosz

Dr. Iwona Dobosz

Department of Physical Chemistry and Metallurgy of Non-Ferrous Metals, AGH University of Science and Technology, 30-059 Krakow, Poland

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 March 2021 in Journal of Porous Materials
Verified
Journal Article
Open access
PDF file
IDIwona Dobosz
Iwona Dobosz
Porous anodic aluminum oxide membranes were fabricated via two-step anodization of aluminum in 0.3 M H2C2O4, 0.3 M H2SO4and 0.17 M H3PO4solutions. The parameters of the oxide film such as: pore diameter (Dp), interpore distance (Dc), porosity (P) and pore density (ρ) can be completely controlled by the operating conditions of the anodization. Additionally, the pore diameters and pore density can be controlled via a chemical treatment (pore opening/widening process). The effect of anodizing conditions such as the applied voltage, type of electrolyte and purity of the substrate on the rate of porous oxide growth are discussed. The obtained results were compared with the theoretical predictions and data that has been reported in the literature. The influence of the duration of chemical etching on the structural features of the oxide membranes was studied. On the based on qualitative and quantitative FFT analyzes and circularity maps, it was found that the nanostructures of anodized aluminum have the maximum order under certain specified conditions. The presence of alloying elements affects not only the rate of oxide growth but also the morphology of the anodic aluminum oxide. The rate of oxide growth depends on the electrolyte type and temperature. During chemical treatment of the oxide films pore diameter increases with the pore widening time and the highest pore widening was observed in phosphoric acid solution.

1 December 2020 in Materials Science and Engineering: B
Verified
Journal Article
Closed access
IDIwona Dobosz
Iwona Dobosz
Dawid KutylaDawid Kutyla
Dawid Kutyla
MKMalgorzata Kąc
Malgorzata Kąc
GWGrzegorz Włoch
Grzegorz Włoch
Piotr ŻabińskiPiotr Żabiński
Piotr Żabiński

22 July 2021 in Materials
Verified
Journal Article
Open access
PDF file
MKMalgorzata Kąc
Malgorzata Kąc
AMAnna Mis
Anna Mis
BDBeata Dubiel
Beata Dubiel
KKKazimierz Kowalski
Kazimierz Kowalski
AZArkadiusz Zarzycki
Arkadiusz Zarzycki
IDIwona Dobosz
Iwona Dobosz
We studied the morphology, structure, and magnetic properties of Fe nanowires that were electrodeposited as a function of the electrolyte temperature. The nucleation mechanism followed instantaneous growth. At low temperatures, we observed an increase of the total charge reduced into the templates, thus suggesting a significant increase in the degree of pore filling. Scanning electron microscopy images revealed smooth nanowires without any characteristic features that would differentiate their morphology as a function of the electrolyte temperature. X-ray photoelectron spectroscopy studies indicated the presence of a polycarbonate coating that covered the nanowires and protected them against oxidation. The X-ray diffraction measurements showed peaks coming from the polycrystalline Fe bcc structure without any traces of the oxide phases. The crystallite size decreased with an increasing electrolyte temperature. The transmission electron microscopy measurements proved the fine-crystalline structure and revealed elongated crystallite shapes with a columnar arrangement along the nanowire. Mössbauer studies indicated a deviation in the magnetization vector from the normal direction, which agrees with the SQUID measurements. An increase in the electrolyte temperature caused a rise in the out of the membrane plane coercivity. The studies showed the oxidation resistance of the Fe nanowires deposited at elevated electrolyte temperatures.

12 February 2025 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
IDIwona Dobosz
Iwona Dobosz
MKMalgorzata Kac
Malgorzata Kac
DKDawid Kutyła
Dawid Kutyła
GWGrzegorz Włoch
Grzegorz Włoch

28 June 2023 in Materials Today Communications
Verified
Journal Article
Closed access
IDIwona Dobosz
Iwona Dobosz
MKMalgorzata Kac
Malgorzata Kac

11 October 2024 in Coatings
Verified
Journal Article
Open access
PDF file
IDIwona Dobosz
Iwona Dobosz
EREwa Rudnik
Ewa Rudnik
The aim of this study was to systematically analyze the influence of potential and the Co(II)–Ru(III) molar ratio on the electrochemical behavior of the Co–Ru system during codeposition from acidic chloride electrolytes. The equilibrium speciation of the baths was investigated spectrophotometrically and compared with theoretical calculations based on the stability constants of Co(II) and Ru(III) complexes. The codeposition of the metals was characterized using electroanalytical methods, including cyclic voltammetry, chronoamperometry, and anodic stripping linear voltammetry. The alloys obtained at different potentials were analyzed for their elemental composition (EDS, mapping), phase composition (XRD), and surface morphology (SEM). The morphology and composition of the alloys were mainly dependent on the deposition potential, which controlled the cobalt incorporation. Ruthenium–rich alloys were produced at potentials of −0.6 V and −0.7 V (vs. SCE). In these conditions, cobalt anomalously codeposited due to the formation of the CoOH+ intermediate, triggered by the intense hydrogen evolution on the ruthenium sublayer. Bulk cobalt electrodeposition began at a potential of around −0.8 V, resulting in the formation of cobalt-rich alloys. The early stages of the electrodeposition were investigated using different nucleation models. A transition from 2D progressive nucleation to 3D instantaneous nucleation at around −0.8 V was identified as being caused by cobalt incorporation. This was well correlated with electroanalytical data, partial polarization curves of alloy deposition, elemental mapping analysis, and the structure of the deposits.