Biosorption is a very effective technique to eliminate the heavy metals present in the wastewater that utilize nongrowing biomass. The adsorption ability of the Periyakulam-2 (PKM-2) variety of Moringa Oleifera leaves (MOLs) to eliminate Pb(II) and Zn(II) ions from an aqueous solution was examined in this work. Fourier transform infrared (FTIR) spectroscopy, field-emission scanning electron microscopy, energy-dispersive X-ray (EDX) analysis, X-ray powder diffraction, and Brunauer–Emmett–Teller methods were used to characterize the PKM-2 variety of MOLs. The set of variables consists of the metal ion initial concentration, a dosage of the adsorbent, and pH were optimized with the help of the response surface methodology to get maximum metal removal efficiency of lead and zinc metals using the PKM-2 MOL biosorbent. A maximum Pb(II) removal of 95.6% was obtained under the condition of initial concentration of metal ions 38 mg/L, a dosage of the adsorbent 1.5 g, and pH 4.7, and a maximum zinc removal of 89.35% was obtained under the condition of initial concentration of metal ions 70 mg/L, a dosage of the adsorbent 0.6 g, and pH 3.2. The presence of lead and zinc ions on the biosorbent surface and the functional groups involved in the adsorption process were revealed using EDX and FTIR analysis, respectively. The adsorption data were evaluated by employing different isotherm and kinetic models. Among the isotherm models, Langmuir’s isotherm showed that the best fit and maximum adsorption capacities are 51.71 and 38.50 mg/g for lead and zinc, respectively. Kinetic studies showed accordance with the pseudo-second-order model to lead and zinc metal adsorption. Thermodynamic parameters confirmed (ΔG° < 0, ΔH° < 0, and ΔS° > 0) that the sorption mechanism is physisorption, exothermic, spontaneous, and favorable for adsorption. The results from this study show that the MOL of the PKM-2 type is a promising alternative for an ecofriendly, low-cost biosorbent that can effectively remove lead and zinc metals from aqueous solutions.
In this work, biochar produced from breadfruit leaves was utilized to remove the toxic Congo red dye. XRD, FTIR, and FESEM-EDX were implemented to characterize the biochar. Response surface methodology (RSM) and the Box-Behnken design (BBD) techniques were used to evaluate Congo red’s optimum adsorption efficiency. The adsorption of Congo red was studied by varying dye concentrations (5–50 mg/L), times (30–240 min), pH (6–9), and dosages (0.5–2 g/100 mL). X-ray diffractometer results show that the structure of biochar is amorphous. The biochar exhibited unbounded OH, aliphatic CH group, and C=O stretch, as shown by the band peaks at 3340 cm−1, 2924 cm−1, and 1625 cm−1 intensities. RSM-BBD design results showed maximum removal efficiency of 99.96% for Congo red at pH 6.37, dye concentration 45 mg/L, time 105 min, and dosage 1.92 g, respectively. The adsorption of Congo red by biochar was successfully modeled using the Langmuir model and pseudo-second-order model. The biochar produced from breadfruit leaves exhibited a high adsorption capacity of 17.81 mg/g for Congo red adsorption. It suggests that the adsorption is both homogenous monolayer and physicochemical.
15 June 2023 in Biomass Conversion and Biorefinery
In this study, a diesel engine was used to operate with blends of light fraction waste cooking oil (LFWCO) with diethyl ether (DEE). DEE was blended as an additive in the 5% to 20% ratio in steps of 5% each. The test indicates that LFWCO+15-DEE produced optimum results regarding performance and emission. The BSFC for LFWCO+15-DEE was found to be higher by about 28.9%, and the BTE was lower by about 7.6%, in contrast to diesel, at 100% operating load, respectively. For LFWCO+15-DEE the EGT was lower by about 11.9%, in contrast to neat diesel, at 100% operating load. The various emissions such as carbon monoxide (CO), nitrous oxide (NO), and smoke opacity for LFWCO+15-DEE were found to be lower by about 32.9%, 25%, and 29.4%, but the NO release was more than other blends and it was about 36%, in contrast to diesel at 100% operating load, respectively.