This study proposes to use reactive copolymers based on glycidyl methacrylate and fluoroalkyl methacrylates with a low fluorine content in the monomer unit as agents to reduce the surface free energy (SFE). This work reveals the effect of the structure and composition of copolymers on the SFE and water-repellent properties of these coatings. On a smooth surface, coatings based on copolymers of glycidyl methacrylate and fluoroalkyl methacrylates with fluorine atoms in the monomer unit ranging from three to seven are characterized by SFE values in the range from 25 to 13 mN/m, which is comparable to the values for polyhedral oligomeric silsesquioxanes and perfluoroalkyl acrylates. On textured aluminum surfaces, the obtained coatings provide time-stable superhydrophobic properties with contact angles up to 170° and sliding angles up to 2°. The possibility of using copolymers based on glycidyl methacrylate and fluoroalkyl methacrylates for the creation of self-cleaning polymer coatings is shown.
This paper discusses the influence of the structure of copolymers based on glycidyl methacrylate and alkyl methacrylates with C6–C18 hydrocarbon side groups on the wettability and sorption properties of surface-modified chitosan aerogels. The grafting of copolymers onto the surface of aerogels was confirmed by elemental analysis, X-ray photoelectron spectroscopy, and Fourier-transform infrared spectroscopy. As a result of the modification, with an increase in the amount of the hydrocarbon substituent alkyl methacrylate, the surface of the resulting materials became hydrophobic with contact angles in the range of 146–157°. At the same time, the water absorption of the aerogels decreased by a factor of 30 compared to that for unmodified aerogels, while the sorption capacity for light oil, diesel fuel, and synthetic motor oil remained at the level of more than 30 g/g. Chitosan aerogels with grafted copolymers based on glycidyl methacrylate and alkyl methacrylates retain biodegradation capacity; however, compared to unmodified chitosan, this process has an induction period.
In the last decade, the task of developing environmentally friendly and cost-effective methods for obtaining stable superhydrophobic coatings has become topical. In this study, we examined the effect of the concentrations of filler and polymer binder on the hydrophobic properties and surface roughness of composite coatings made from organic–aqueous compositions based on hexyl methacrylate (HMA) and glycidyl methacrylate (GMA) copolymers. Silicon dioxide nanoparticles were used as a filler. A single-stage “all-in-one” aerosol application method was used to form the coatings without additional intermediate steps for attaching the adhesive layer or texturing the substrate surface, as well as pre-modification of the surface of filler nanoparticles. As the ratio of the mass fraction of polymer binder (Wn) to filler (Wp) increases, the coatings show the lowest roll-off angles among the whole range of samples studied. Coatings with an optimal mass fraction ratio (Wn/Wp = 1.2 ÷ 1.6) of the filler to polymer binder maintained superhydrophobic properties for 24 h in contact with a drop of water in a chamber saturated with water vapor and exhibited roll-off angles of 6.1° ± 1°.
This study presents water-repellent coatings for pine wood surfaces based on epoxy varnish modified with glycidyl methacrylate–(fluoro)alkyl methacrylate copolymers, achieving superhydrophobic properties with contact angles up to 155° while maintaining the natural texture of the wood. The influence of the application method on the microtexture and water-repellent properties of the coatings has been demonstrated. Incorporating functional copolymers considerably improves water resistance: after 60 days of immersion, water absorption is reduced more than threefold compared to coatings made with unmodified epoxy varnish. Furthermore, the coatings maintain their water-repellent properties and preserve the wood’s appearance even after six months of exposure to the tropical climate of South Vietnam.
1 January 2022 in Izvestia Volgograd State Technical University