A.Y.T. Leung

Dr. A.Y.T. Leung


Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 April 2010 in Scripta Materialia
Verified
Journal Article
Closed access
XGX. Guo
X. Guo
ALA.Y.T. Leung
A.Y.T. Leung
ACA.Y. Chen
A.Y. Chen
HAIHUI RUANHAIHUI RUAN
HAIHUI RUAN
JLJian Lu
Jian Lu

7 July 2004 in Journal of Vibration and Acoustics
Verified
Journal Article
Closed access
PDF file
QDQian Ding
Qian Ding
ALA.Y.T. Leung
A.Y.T. Leung
An experimental test rig is built to verify the dynamics of a multi-bearing rotor. It consists of two flexibly coupled shafts and is connected to a motor at one end via a flexible coupling. Each of the shafts is supported at the ends by two hydrodynamic bearings and is attached with two disks with equal and unequal masses, respectively. The mathematical model of the test rig is developed and is simulated numerically. The non-stationary dynamic responses of the system during speed-up with a constant angular acceleration are shown, respectively, by the non-stationary bifurcation diagrams, the selected time flows, and the spectrum cascades. Experiments are then carried out on the test rig. Generally, the numerical results are verified qualitatively by the experiments. Both results indicate that the non-synchronous whirls of the two shafts influence each other when flexibly coupled together. In particular, a new phenomenon is found for the four-bearing rotor system: the pre-existing non-synchronous whirl/whip resulted from the instability of one shaft can activate the onset of oil instability of another shaft. In the theoretical simulation, this phenomenon represents the rapid increase of the non-synchronous whirl orbit, whereas in the experiment, it represents the simultaneous existence of two whirl/whip frequencies in the spectra.

9 August 2006 in International Journal for Numerical Methods in Engineering
Verified
Journal Article
Closed access
PDF file
ALA.Y.T. Leung
A.Y.T. Leung
XXXinsheng Xu
Xinsheng Xu
QGQian Gu
Qian Gu
CLC. T. O. Leung
C. T. O. Leung
JZJ. J. Zheng
J. J. Zheng

18 February 2005 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
ALA.Y.T. Leung
A.Y.T. Leung
XGX. Guo
X. Guo
XHX. Q. He
X. Q. He
SKS. Kitipornchai
S. Kitipornchai
An idea of “spatial periodic strain” is proposed and an equilibrium relationship is established for the mechanics of zigzag single-walled carbon nanotubes (SWCNTs). An efficient approach is presented to investigate mechanical properties of zigzag SWCNT, and its validity is demonstrated by comparing its calculation results with existing results.

1 October 2009 in International Journal of Solids and Structures
Verified
Journal Article
Closed access
PDF file
ZZZ.H. Zhou
Z.H. Zhou
XXX.S. Xu
X.S. Xu
ALA.Y.T. Leung
A.Y.T. Leung

1 January 2008 in Journal of Engineering Mechanics
Verified
Journal Article
Closed access
HLHeung Fai LAM
Heung Fai LAM
Ching Tai NgChing Tai Ng
Ching Tai Ng
ALA.Y.T. Leung
A.Y.T. Leung
The problem of crack detection has been studied by many researchers, and many methods of approaching the problem have been developed. To quantify the crack extent, most methods follow the model updating approach. This approach treats the crack location and extent as model parameters, which are then identified by minimizing the discrepancy between the modeled and the measured dynamic responses. Most methods following this approach focus on the detection of a single crack or multicracks in situations in which the number of cracks is known. The main objective of this paper is to address the crack detection problem in a general situation in which the number of cracks is not known in advance. The crack detection methodology proposed in this paper consists of two phases. In the first phase, different classes of models are employed to model the beam with different numbers of cracks, and the Bayesian model class selection method is then employed to identify the most plausible class of models based on the set of measured dynamic data in order to identify the number of cracks on the beam. In the second phase, the posterior (updated) probability density function of the crack locations and the corresponding extents is calculated using the Bayesian statistical framework. As a result, the uncertainties that may have been introduced by measurement noise and modeling error can be explicitly dealt with. The methodology proposed herein has been verified by and demonstrated through a comprehensive series of numerical case studies, in which noisy data were generated by a Bernoulli–Euler beam with semirigid connections. The results of these studies show that the proposed methodology can correctly identify the number of cracks even when the crack extent is small. The effects of measurement noise, modeling error, and the complexity of the class of identification model on the crack detection results have also been studied and are discussed in this paper.