Purlins made from galvanised steel in fertiliser warehouses have often been considered less efficient, necessitating a new purlin made using corrosion-resistant material to increase building efficiency. This study was an attempt to design a nine-metre purlin from glass-fibre-reinforced polymer (GFRP) composite material for a new fertiliser warehouse in Bontang-East Kalimantan, Indonesia. The purlin design selected in this study was the Z profile of pultruded beams from GFRP composite material that met the criteria of an efficient purlin, such as corrosion resistance, compact stacking, and ability to withstand technical loads. In particular, the Z profile becomes compact when stacked, and the GFRP material used is corrosion-resistant yet affordable. The primary materials for GFRP composites consist of long yarn glass fibre bundles for reinforcement and unsaturated polyester resin (UPR) for the matrix. Material strength modelling was based on analytical and finite element approaches. The analysis shows that the most considerable normal stress of “64.41 MPa” occurred at the two fixed end supports, while the most significant deflection of “45.9 mm” occurred at the mid-span of the purlin structure. The purlin structure was considered safe, as the strength and deflection were below the threshold. Thus, the Z profile of the pultruded purlin beams built using the GFRP composite material meets the technical criteria.
22 September 2023 in Pertanika Journal of Tropical Agricultural Science
Aquaponics with bio-floc can potentially offer sustainable food production with zero waste as it allows farming plants and fish simultaneously, whereby the former use fish waste as their nutrient sources, while the latter receives cleaner water from the plants in a closed-loop system. In the aquaponics system, additional nutrients are usually added to support optimal plant growth, but it is suggested that the amount of such chemical nutrients should be controlled to prevent any harm to the fish. Furthermore, the plant and fish growth rates are influenced by the nutrients and the culture media used. This study aims to examine the effect of nutrition (full-nutrient and half-nutrient treatments) and different types of culture mediums (rockwool, rockwool-perlite, and rockwool-husk) on the growth rates of pak choi (Brassica rapa) and catfish (Clarias gariepinus) using split-plot design. Findings show that the half-nutrient treatment yielded a 17.12% higher plant growth rate and 23.87% heavier catfish weight than the full-nutrient treatment, but these treatments did not affect the fish survival rate. It was also observed that using different culture mediums did not result in any significant difference.
15 October 2023 in Cylinder : Jurnal Ilmiah Teknik Mesin
Aktivitas manusia telah berubah dari waktu ke waktu. ketika teknologi belum ditemukan, semuanya rumit. Namun kini, penemuan teknologi telah membantu kita dengan cara yang lebih efektif dan lebih mudah. Hal ini membuat aktivitas kita sehari-hari menjadi jauh lebih mudah. Seiring dengan perkembangan teknologi yang pesat, proses jual beli menjadi lebih mudah karena dapat dilakukan melalui e-commerce. Namun, hal tersebut berdampak pada beberapa orang seperti orang menjadi tidak produktif dalam bekerja karena khawatir dengan kemasannya. Seringkali, ada paket yang datang dengan kondisi tidak sesuai harapan, serta tidak higienis karena telah mengalami banyak kontak dari orang-orang. Oleh karena itu, dibuatlah kotak penerima paket pintar (Smart Package Receiver) berbasis IoT menggunakan modul Wi-Fi ESP8266. Teknologi ini membantu menghilangkan kekhawatiran tentang kebersihan paket. Ketika kurir memasukkan paket ke dalam kotak, modul akan segera mengirimkan notifikasi melalui aplikasi discord ke perangkat-perangkat penerima. Kemudian, Sinar UV akan dipaparkan ke paket untuk mensterilkannya. Tujuan dari Smart Package Receiver adalah untuk menciptakan suatu sistem yang memudahkan masyarakat dalam menerima paketnya, juga menguntungkan bagi kurir dan penerima.
21 April 2022 in Cylinder : Jurnal Ilmiah Teknik Mesin
Penggunaan Printer 3D saat ini sudah semakin luas dan banyak macam bentuk yang dapat dibuat karena sistem layer-by-layer. Pada penelitian ini dilakukan pengukuran laju aliran volumetrik (debit) menggunakan material Thermoplastic Polyurethane (TPU) sebagai filamen printer 3D. TPU memiliki karakteristik material yang elastis. Pada eksperimen, dapat dibuktikan bahwa fluida TPU memiliki sifat non-newtonian, yaitu shear-thinning karena semakin besar temperatur dan kecepatan input yang diberikan pada fluida menyebabkan peningkatan debit outlet. Pengukuran laju aliran volumetrik (debit) fluida ditujukan agar dapat diketahui pengaruh viskositas fluida terhadap kestabilan debit aliran. Data hasil eksperimen dibandingkan dengan data hasil simulasi menggunakan perangkat lunak ANSYS Fluent 17.2. Data hasil simulasi belum dapat menunjukkan pengaruh viskositas terhadap debit aliran diakibatkan data yang dimasukkan pada perangkat lunak hanya berdasarkan dari jurnal dan lembaran data spesifikasi produk pabrik tertentu.
15 April 2023 in Cylinder : Jurnal Ilmiah Teknik Mesin
Jurnal ini membahas tentang perancangan prototipe dari excavator dengan sistem penggerak lengan excavator menggunakan sistem hidrolik yang diterapkan menggunakan syringe. Perkembangan dalam dunia industri dan teknologi telah menuntut penggunaan mesin produksi yang mudah dikendalikan dan memiliki keakuratan maupun kekuatan yang sesuai. Sistem tenaga fluida adalah salah satu jenis sistem yang bekerja dengan memanfaatkan fluida gas maupun cair untuk melakukan transmisi gaya, sistem tersebut memiliki sensitivitas dan kekuatan yang baik untuk membantu kerja sebuah mesin secara mekanis Sistem tenaga fluida yang digunakan dalam penelitian ini berjenis hidrolik sederhana yang memanfaatkan air sebagai fluida kerja, sedangkan sistem kontrol akan dirancang dengan memanfaatkan perangkat ESP 32 dan server milik Blynk. Hasil pengujian yang didapatkan yaitu hidrolik pada lengan pertama (Boom) mampu menarik beban hingga 2,55 N, hidrolik pada lengan tengah (Arm) mampu menarik beban hingga 2,5 N, hidrolik ketiga menunjukkan bahwa bucket mampu menarik beban hingga 1,4 N.
10 December 2023 in Journal of Science and Applicative Technology
Improving medical services is continuously prioritized for the sake of achieving the welfare of all people in the world, and by providing good services in the medical field, people's needs will be increasingly fulfilled. Limitations of movement in someone with a disability, such as persons with disabilities tetraplegic in terms of mobility, are often obstacles. Therefore, a media-assisting movement is needed. This study designed an electric wheelchair that can help users with disabilities tetraplegic in moving without the need for too much force as in a standard wheelchair. This electric wheelchair uses automation by utilizing Accelerometer, which can detect vectors or so-called gyroscopes and connect with Arduino as the processor is continued to the DC motor as the driving force. Based on the test data, it was found that the design of this wheelchair moves as desired. This can be seen from the change in speed of the driving motor to changes in the tilt of the accelerometer mounted on the head. In the forward motion test, the maximum motor speed is 35 RPM when the accelerometer angle is at a slope of 64.7o positive axes. Meanwhile, the backward movement of the wheelchair occurs when the accelerometer is at a slope of -21.1o and produces a speed of 11.2 RPM on wheels. The rider's maximum load is designed to be 50 Kg.