Gutters made of glass-fibre-reinforced polymer (GFRP) are usually produced with a three-millimetre thickness. The fillers are mixed into unsaturated polyester (UP) resin, which is intended to make the composite material more affordable. This study aims to examine the effects of the addition of alumina trihydrate (ATH), calcium carbonate (CC), and a mixture of ATH and CC of 15 and 30 parts per hundredweight of resins (PHR) on the material properties of the three-millimetre-thick three-layered GFRP composites. The properties observed included physical properties, namely, specific gravity and water absorption, chemical properties such as burning rate, and mechanical properties such as hardness, flexural strength, and toughness. The effects of the fillers on the voids and interfacial bond between the reinforcing fibre and matrix were analysed using the flexural fracture observation through scanning electron microscopy (SEM). The results showed that the addition of fillers into the UP resin led to an increase in the density, hardness, flexural strength, modulus of elasticity, and toughness but a decrease in water absorption and burning rate in a horizontal position. This information can be helpful for manufacturers of gutters made of GFRP in selecting the appropriate constituent materials while considering the technical and economic properties.
It is difficult to obtain suitable fire resistance and mechanical properties for glass-fiber-reinforced polymer (GFRP) roof material in industrial applications. Although some efforts to improve the fire resistance properties of GFRP have been carried out, in practice this sometimes degrades the mechanical properties. Therefore, the base materials, such as filler and reinforcing fiber, must be appropriately combined to simultaneously improve both fire resistance and mechanical properties. The present study examines improvements in GFRP roof material by investigating the effect of aluminium trihydrate (ATH) as a filler and the combination of a chopped strand mat (CSM) with woven roving (WR) and stitched mat (STM) fibers as the reinforcement in a composite GFRP roof structure. The roof samples were prepared following industrial machine standards using the specified materials. The mechanical properties of GFRP were evaluated using tensile, flexural and impact tests, following ASTM D638, ASTM D790 and ASTM D256 standards, respectively. The fire properties were examined through fire tests following the ASTM D635 standard. The results show that the GFRP roof composed of CSM/WR fibers had a 40% higher tensile strength (103.5 MPa) compared with the GFRP roof without CSM fibers (73.8 MPa). The flexural strength of the GFRP roof with CSM/WR fibers was also 57% higher than the roof without fibers, with a ratio of 315.61 MPa to 201 MPa. With the use of CSM/WR fibers, the fire resistance also increased by 23%, resulting in a ratio of 4.31 mm/min to 5.32 mm/min. These results demonstrate that the combination of CSM/WR fibers as a reinforcement would be an excellent option for producing an improved GFRP roof with better industrial properties, especially when producing improved GFRP roofs using a continuous lamination machine.
Background: The latest global agreement on net-zero emissions encourages new studies on production inventory optimization that promote carbon emissions reduction without harming a company’s profit performance, particularly because certain carbon-pricing regulations bind manufacturing companies. Methods: This study aims to develop a production inventory model that considers direct and indirect emissions in three emission scopes. It incorporates emissions from production, material handling, transportation, and waste disposal for further treatment under a carbon cap-and-trade regulation. With the help of Maple software, a convex total cost function was solved. Results: The results show that the optimum production quantity depends on the values of demand, setup cost, holding cost, fixed cost per delivery, fixed cost for waste disposal, and other parameters related to carbon prices. This study also found that the total cost was highly dependent on the values of the carbon cap, carbon price, and delivery distance. Meanwhile, changes in the delivery distance and fuel emissions standard significantly impacted total emissions. Conclusions: The proposed model can guide manufacturing companies in setting the optimum production quantity per cycle. Moreover, they must carefully manage the delivery and setting of the carbon cap and carbon price from the government.
A modern agricultural method of cultivating mustard greens and watercress with a hydroponic system in a pilot greenhouse has been implemented by a group of farmers in Cisauk-Tangerang, Banten, Indonesia. The characteristic tropical climate south of the equator causes high temperatures and humidity in the greenhouse. This study aims to control the temperature and humidity in the greenhouse using the misting method so that the temperature and humidity are not more than 33 °C and 85%, respectively. A misting system designed by the main equipment consists of a water flow control pump, temperature and humidity sensors, water mist spray nozzles, and water flow settings for intermittent drizzle for five minutes ON and ten minutes OFF using the internet of things module program. In addition to setting the water discharge intermittently, another limitation for the pump to be OFF is a minimum temperature benchmark of 28 °C and a maximum humidity of 85%. The temperature does not exceed 33 °C, and the humidity setting of 85% is obtained by adjusting the mass flow of water during the day according to the time sequence from 7 a.m. to 5 p.m.: 7 a.m. to 8 a.m. using 50 L/h, 8 a.m. to 10 a.m. using 60 L/h, 10 a.m. to 11 a.m. using 100 L/h, 11 a.m. to 1 p.m. using 120 L/h, 1 p.m. to 2 p.m. using 80 L/h, 2 p.m. to 3 p.m. using 60 L/h, and 3 p.m. and after using 0 L/h or the misting system is turned off.
19 July 2023 in Journal of Advanced Research in Applied Sciences and Engineering Technology
Rigid polyurethane (RPU) foams as roof insulation have become increasingly popular in Southeast Asian countries and have been extensively used for absorbing sound and reducing noise because of their good sound damping, viscoelasticity, and low density. In this study, the RPU foam composite reinforced bamboo fiber was investigated by physical characterization by SEM, TGA, and FTIR, and the sound absorption was measured by the Impedance Tube Test. The morphology result of the RPU foam composite indicates the size of the diameter pore influenced the sound absorption by adding bamboo fiber as a filler. The thermal degradation of the presence of lignin in the bamboo fiber at the temperature range of 400 °C to 500 °C and the total weight loss is 76 % at 429 °C temperature. FTIR spectrum shows that the peak at 2890 to 2935 cm-1 are indicated –CH stretching vibrations and characteristics for bamboo fiber can be used in polymer composites. The sound absorption of RPU 25 foam composite reinforced bamboo fiber was found 0.74 absorbance at a frequency of 1250 Hz. RPU foam reinforced bamboo fiber as a filler has the highest transmission loss RPU 35 is 21 dB at a frequency range of 1600 Hz. The findings indicate by increasing the content of bamboo fiber as filler, the diameter of the open pore of RPU 25 and RPU 35 foam composite had the potential for sound absorption to absorb at low frequency to achieve greater sound absorption for roof insulation.
2 June 2024 in Journal of Advanced Research in Applied Mechanics
The performance of roof insulation such as polyurethane decreased due to problems such as insufficient absorption and poor thermal insulation performance, especially during rainstorms. The aims of this study are to investigate the physical property and its potential reinforced material such as rigid polyurethane doped with treated and untreated bamboo fiber composite (RPU-BF) at different ratios of 0, 25, 30, 35, and 40% of bamboo fibers as an insulation material for roof applications. The bamboo fibers were treated by using silane coupling agent treatment. The rigid polyurethane composite samples were prepared and then laminated bamboo fiber to overcome the sound problem in roofs. The physical characterization was investigated by Water Contact Angle (WCA), the morphological by Scanning Electron Microscopy (SEM), Thermo-gravimetric Analysis (TGA), and Fourier Transform Infrared Spectroscopy (FTIR) Analysis. The results showed that the treated bamboo fiber had a 192.5° water contact angle as a super hydrophobic property due to the presence of the chemical bonds Si-O-Si and Si-O-C in the silane coupling agent treatment. The morphology showed that 30% ratios of RPU-BF-T30 give the smallest pore diameter size. The peak of thermal degradation temperature of untreated and treated bamboo fiber was increased from 320°C to 350 °C with a weight loss of 80% to 50%. The treated bamboo fiber exhibited peaks at 3010–3040 cm-1 were associated with stronger Si-O-Si bonding, indicating the formation of new chemical bonds between bamboo fiber and silane coupling agent due to the ester bond from the cellulose, lignin, and hemicellulose. Thus, there was a similar trend peak in the functional chemical group in the FTIR spectrum of the RPU-BF composite. This result shows that RPU-BF composite had the potential of the optimum ratio of bamboo fiber as an insulation material for local communities and beneficial to the bamboo industry.