Ihor Romanenko

Mr. Ihor Romanenko

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 August 2020 in Aerospace technic and technology
Verified
Journal Article
Closed access
PDF file
IRIhor Romanenko
Ihor Romanenko
АБАлександр Витальевич Белогуб
Александр Витальевич Белогуб
The article touches upon the issues of the operating process in the elements of the external gear pump modeling. The external gear pump is the part of the gas turbine engine and pumps a low-viscosity fluid – kerosene. The article shows that sleeve bearings in such pumps continue to operate at boundary friction modes while rotation speed is increased. It also shows that the end and radial clearances are variable, and the drain system is not optimal which prevents the modeling of the system by classic approach. The main elements of the pumping unit of the external gear pump are described in the article. A simplified geometric model, which forms the basis for the analysis of the pump operation, is given as well. The problems arising during the design stage, fine-tuning, and operation of external gear fuel pumps are briefly described. A preliminary analysis of the design methods showed that several parameters of the working process are not studied well enough to provide the basis for optimal construction design and its qualitative assessment within the design stage. The description of gears operation, the system of end clamping, end, and radial plain bearings is given. The analysis of pressure distribution models is given. The analysis takes into account pressure distribution from linear distribution in the delivery chamber to the pressure drop on one tooth. Distributions from different calculation methods and literature sources are compared as well. The features of bearing loading and the conditions of their operation and lubrication are described. Based on the preliminary calculations, recommendations in the literature, and experimental data, the operation features analysis of the gear fuel pump of the gas turbine engine is carried out. There are defined problems that will provide answers to the main modeling issues in the article: pressure distribution in the intertooth displacement chamber during stationary and transient operating; fluid leakage through variable end clearances and radial clearances; dynamic of the gears and associated parts movement; the influence of external conditions (temperatures, pressures, external vibrations, etc.) on the operation of the pump in general.

28 April 2021 in Aerospace technic and technology
Verified
Journal Article
Closed access
PDF file
ОБОлександр Віталійович Білогуб
Олександр Віталійович Білогуб
IRIhor Romanenko
Ihor Romanenko
ОГОлександр Володимирович Гудошник
Олександр Володимирович Гудошник
СТСергій Олександрович Тристан
Сергій Олександрович Тристан
The paper is about the performance capability of the journal bearings as a support of the fuel gear pump for gas turbine engines (GTE). Supports of the external gear pump usually operate in semi-dry friction conditions, which reduces residual life and is one of the limiting factors. For this investigation, the serial gear pump was chosen with the following parameters: the number of teeth z = 14, module m = 3.8, gear-loading Р = 7800 N. The authors have studied options for a pump with an electrical and mechanical (from the rotor of the GTE) drive. The main criterion for studying the bearing capacity is the minimum thickness of the working layer of a fluid with low viscosity (kerosene). For modeling, a common theory is used based on solutions of differential equations of the viscous fluid hydrodynamics, which relate pressure, velocity, and viscous shear resistance. For technological reasons, the minimum allowable kerosene layer is limited to 5 μm. The conducted analysis considers the multi-lobe (2-, 3- and 4-lobe) bearings with different lobe orientations relative to the force vector. It was found that the 2-lobe bearing has the best load capacity (provides the largest layer of kerosene). According to the results of the previous investigation for further work, the 2-lobe bearing was chosen. The influence of load, setting gap, eccentricity, the specific radius of lobe curvature, shaft length on the bearing load capacity was analyzed. A rational type of bearing design was proposed based on the load capacity criterion (the minimum layer of working fluid). It was shown that the hydrodynamic 2-lobe bearing can be sufficiently effective for the supports of the gear fuel pumps of GTE. Based on the results of the investigation, 2 variants of the pumping unit designs were proposed. The first one for the pump driven by the gas turbine engine rotor with parameters z = 19, m = 3.3, gears width B = 34, shaft diameter DS = 48, and shaft length LS = 56 (P = 10.2kN). The second one for the electrically driven pump, z = 28, m = 1,8, B = 15, DS = 34, and LS = 41 (P = 3.8 kN). The minimum angular velocity for the pump variants is 470 and 1055 rad/s, respectively. According to the investigation results, it was proposed to conduct related studies of the working process in pumps and bearings.

24 April 2023 in Aerospace technic and technology
Verified
Journal Article
Open access
PDF file
IRIhor Romanenko
Ihor Romanenko
OBOleksandr Bilohub
Oleksandr Bilohub
This article analyzes the possibility of increasing the efficiency of the gear pump operating cycle by using a jet pump as a booster stage. The design of gear pumps is performed for one mode, and most often, it is a mode with minimum speed and high consumption relative to rotation speed. For gas turbine engines, this is the take-off mode, in which the aircraft operates for a few minutes of the entire flight cycle. In other modes, the pump capacity is excessive, reaching more than twice the value in some operational conditions. Due to the excess capacity, overflow valves are used to synchronize the operation of the engine and pump. This approach is a classic solution, but it creates additional mechanical losses and, as a result, reduces the efficiency of the operating cycle of the pump. Therefore, there is a need to improve the matching of engine requirements and pump performance. In this article, a solution that can improve the operating cycle of pumping units within the framework of a classical drive box assembly was analyzed. In the introductory section, the generalized flight cycle of a transport aircraft is analyzed. Based on the results, the modes were determined for which the design calculations of the jet pump were performed. First, the relative characteristics of pressure increase and efficiency are considered. The geometric and operational boundary conditions are accepted considering the fuel overflow relative to the generalized flight cycle. The obtained characteristics are used as a basis for selecting the geometric ratio for the modes with the highest pressure and efficiency. Based on these results, the geometric dimensions of the main sections and the value of the pressure increase at the outlet of the jet pump were obtained. Based on the characteristics of the pressure increase behind the jet pump, the relative characteristics of the reduction in power consumption in the gear pump shaft were obtained. Considering the level of overflow and operating time, the use of a jet pump will save about 50% of the energy input. This is a direct improvement in the operating cycle, and the increased pump inlet pressure will also reduce bearing wear, increase cavitation resistance, and reduce wear from cavitation erosion.