A metal-free β-ketoenamine-based COF was synthesized and applied for photocatalytic CO2 reduction and H2O oxidation without other additives at low CO2 concentrations. The mechanism and rate equations for the reactions were proposed.
High conductivity two-dimensional (2D) materials have been proved to be potential electrode materials for flexible supercapacitors because of its outstanding chemical and physical properties. However, electrodes based on 2D materials always suffer from limited electrolyte-accessible surface due to the restacking of the 2D sheets, hindering the full utilization of their surface area. In this regard, an electrolyte-mediated method is used to integrate dense structure reduced graphene oxide/MXene (RGM)-electrolyte composite films. In such composite films, reduced graphene oxide (RGO) and MXene sheets are controllable assembly in compact layered structure with electrolyte filled between the layers. The electrolyte layer between RGO and MXene sheets forms continuous ion transport channels in the composite films. Therefore, the RGM-electrolyte composite films can be used directly as self-supporting electrodes for supercapacitors without additional conductive agents and binders. As a result, the composite films demonstrate enhanced volumetric specific capacity, improved volumetric energy density and higher power density compared with both pure RGO electrode and porous composite electrode prepared by traditional methods. Specifically, when the mass ratio of MXene is 30%, the electrode delivers a volumetric specific capacity of 454.9 F·cm−3 with a high energy density of 39.4 Wh·L−1. More importantly, supercapacitors based on the composite films exhibit good flexibility electrochemical performance. The investigation provides a new approach to synthesize dense structure films based on 2D materials for application in high volumetric capacitance flexible supercapacitors.
Clarifying the mechanism for the gas transportation in the emerging 2D materials-based membranes plays an important role on the design and performance optimization. In this work, the corresponding studies were conducted experimentally and theoretically. To this end, we measured the gas permeances of hydrogen and nitrogen from their mixture through the supported MXene lamellar membrane. Knudsen diffusion and molecular sieving through straight and tortuous nanochannels were proposed to elucidate the gas transport mechanism. The average pore diameter of 5.05 Å in straight nanochannels was calculated by linear regression in the Knudsen diffusion model. The activation energy for H2 transport in molecular sieving model was calculated to be 20.54 kJ mol−1. From the model, we can predict that the gas permeance of hydrogen (with smaller kinetic diameter) is contributed from both Knudsen diffusion and molecular sieving mechanism, but the permeance of larger molecular gases like nitrogen is sourced from Knudsen diffusion. The effects of the critical conditions such as temperature, the diffusion pore diameter of structural defects, and the thickness of the prepared MXene lamellar membrane on hydrogen and nitrogen permeance were also investigated to understand the hydrogen permeation difference from Knudsen diffusion and molecular sieving. At room temperature, the total hydrogen permeance was contributed 18% by Knudsen diffusion and 82% by molecular sieving. The modeling results indicate that molecular sieving plays a dominant role in controlling gas selectivity.
A novel metal-anchored COF was synthesized and applied to photocatalytic conversion of CO2 and H2O into widely adjustable syngas. The reaction intermediates, electron transfer pathway and syngas generation mechanism were discussed in depth.
As a possible novel cost-effective method for oxygen production from air separation, ion-conducting ceramic membranes are becoming a hot research topic due to their potentials in clean energy and environmental processes. Oxygen separation via these ion-conducting membranes is completed via the bulk diffusion and surface reactions with a typical example of perovskite oxide membranes. To improve the membrane performance, silver (Ag) deposition on the membrane surface as the catalyst is a good strategy. However, the conventional silver coating method has the problem of particle aggregation, which severely lowers the catalytic efficiency. In this work, the perovskite oxide La0.8Ca0.2Fe0.94O3−a (LCF) and silver (5% by mole) composite (LCFA) as the membrane starting material was synthesized using one-pot method via the wet complexation where the metal and silver elements were sourced from their respective nitrate salts. LCFA hollow fiber membrane was prepared and comparatively investigated for air separation together with pure LCF hollow fiber membrane. Operated from 800 to 950 °C under sweep gas mode, the pure LCF membrane displayed the fluxes from 0.04 to 0.54 mL min−1 cm−2. Compared to pure LCF, under similar operating conditions, the flux of LCFA membrane was improved by 160%.