Interfacial interaction is one of the most important factors in the construction of high-performance graphene-based elastomer composites. In this paper, graphene/poly (styrene-b-isoprene-b-styrene) (SIS) composites were prepared with solution mixing followed by an evaporation-induced self-assembly process. Various techniques such as scanning electron microscopy, UV-vis absorption spectra, tensile testing, Shore A hardness, surface resistance, thermal conductivity, and thermogravimetric analysis were conducted to characterize the microstructure and properties of the obtained composites. The results showed that the π–π stacking interfacial interaction between phenyl groups of SIS and graphene play an important role in the properties’ improvement, and the effect of interfacial interaction on the properties was revealed.

Dye pollution is a serious issue in current environment protection, and bio-based adsorbents have been receiving much attention in wastewater treatment, due to their low cost, renewable, and environmentally friendly characteristics. Bio-based sodium alginate/lignin composite (SA/Lig) hydrogel beads were fabricated by a facile cross-linking with calcium ion and used for the removal of methylene blue (MB). The obtained SA/Lig microbeads were characterized with SEM, FTIR, and TG, and the effect of lignin content, pH, and temperature on the MB adsorption was investigated. The results indicated that the introduction of aromatic lignin can not only enhance thermal stability but also can improve the adsorption performance. Under optimal conditions, the maximum adsorption capacity (254.3 mg/g) was obtained for the SA/Lig-20% beads, with a removal efficiency of 84.8%. The adsorption process for MB is endothermic, and the rate-limiting step is chemical adsorption. The removal efficiency is higher than 90% after five cycles, revealing that the prepared beads show good regeneration ability.

With the development of science and technology, photocatalytic technology is of great interest. Nanosized photocatalysts are easy to agglomerate in an aqueous solution, which is unfavorable for recycling. Therefore, hydrogel-based photocatalytic composites were born. Compared with other photocatalytic carriers, hydrogels have a three-dimensional network structure, high water absorption, and a controllable shape. Meanwhile, the high permeability of these composites is an effective way to promote photocatalysis technology by inhibiting nanoparticle photo corrosion, while significantly ensuring the catalytic activity of the photocatalysts. With the growing energy crisis and limited reserves of traditional energy sources such as oil, the attention of researchers was drawn to natural polymers. Like almost all abundant natural polymer compounds in the world, cellulose has the advantages of non-toxicity, degradability, and biocompatibility. It is used as a class of reproducible crude material for the preparation of hydrogel photocatalytic composites. The network structure and high hydroxyl active sites of cellulose-based hydrogels improve the adsorption performance of catalysts and avoid nanoparticle collisions, indirectly enhancing their photocatalytic performance. In this paper, we sum up the current research progress of cellulose-based hydrogels. After briefly discussing the properties and preparation methods of cellulose and its descendant hydrogels, we explore the effects of hydrogels on photocatalytic properties. Next, the cellulose-based hydrogel photocatalytic composites are classified according to the type of catalyst, and the research progress in different fields is reviewed. Finally, the challenges they will face are summarized, and the development trends are prospected.

The morphology and intermolecular interaction are two of the most important factors in the design of highly efficient dye adsorbent in the industry. Millimeter-sized, bead-type, bio-based lignin/chitosan (Lig/CS) adsorbent was designed for the removal of Congo red (CR), based on the electrostatic attraction, π-π stacking, and hydrogen bonding, which were synthesized through the emulsification of the chitosan/lignin mixture followed by chemical cross-linking. The effects of the lignin/chitosan mass ratio, initial pH, temperature, concentration, and contact time on the adsorption were thoroughly investigated. The highest adsorption capacity (173 mg/g) was obtained for the 20 wt% Lig/CS beads, with a removal rate of 86.5%. To investigate the adsorption mechanism and recyclability, an evaluation of the kinetic model and an adsorption/desorption experiment were conducted. The adsorption of CR on Lig/CS beads followed the type 1 pseudo-second-order model, and the removal rate for CR was still above 90% at five cycles.

Due to the specific recognition performance, imprinted polymers have been widely investigated and applied in the field of separation and detection. Based on the introduction of the imprinting principles, the classification of imprinted polymers (bulk imprinting, surface imprinting, and epitope imprinting) are summarized according to their structure first. Secondly, the preparation methods of imprinted polymers are summarized in detail, including traditional thermal polymerization, novel radiation polymerization, and green polymerization. Then, the practical applications of imprinted polymers for the selective recognition of different substrates, such as metal ions, organic molecules, and biological macromolecules, are systematically summarized. Finally, the existing problems in its preparation and application are summarized, and its prospects have been prospected.

Materials with excellent biocompatibility and targeting can be widely used in the biomedical field. Hydrogels are an excellent biomedical material, which are similar to living tissue and cannot affect the metabolic process of living organisms. Moreover, the three-dimensional network structure of hydrogel is conducive to the storage and slow release of drugs. Compared to the traditional hydrogel preparation technologies, ionizing radiation technology has high efficiency, is green, and has environmental protection. This technology can easily adjust mechanical properties, swelling, and so on. This review provides a classification of hydrogels and different preparation methods and highlights the advantages of ionizing radiation technology in smart hydrogels used for biomedical applications.