The stray-light suppression of a large off-axis three-mirror anastigmatic space camera has been a hot topic, and this study proposes a composite stray-light suppression strategy that effectively suppresses stray light using the combination of a baffle, retaining ring, and internal antistray light measures. Additionally, the light barrier of the third mirror with a three-layered structure was designed to further optimize the composite stray-light suppression system. At the stray-light simulation analysis stage, in view of the limitations of the Torrance–Sparrow scattering analysis model, an analysis model with wide adaptability is proposed, which can be applied to the stray-light simulation analysis of large-size mirrors with rough surfaces. The simulation results indicate that the point source transmittance of the composite stray-light suppression strategy proposed in this paper is of the order of 10⁻⁵ before installing the light barrier of the third mirror, and the veiling glare index of the full field of view is less than 5.8%. After installing the light barrier of the third mirror, the point source transmittance reached the order of 10⁻⁸, and the veiling glare index of the full field of view was less than 1.31%. Moreover, the influence of the light barrier of the third mirror on the modulation transfer function of the system was less than 2.3%. The modulation transfer function test of the large-width off-axis three-mirror anastigmatic space camera in a simulated vacuum on-orbit environment was completed, and the test results indicated that the negative impact of the light barrier of the third mirror on the modulation transfer function was less than 3.6%. Moreover, an out-of-field imaging test of the space camera was conducted and the results showed that the image was clear, and the SNR reached 80 dB. The simulation and experimental results prove that the solution in this study can effectively solve the problem of stray-light suppression for large off-axis three-mirror anastigmatic space cameras.

Bayer filter color cameras are more and more widely used in the field of aerospace remote sensing, but the Bayer filter causes great degradation in image quality; therefore, obtaining a means of achieving the high-precision measurement of the modulation transfer function (MTF) of Bayer filter color cameras is an urgent problem. In order to solve this problem, this paper develops a slanted-edge method via three steps: the detection of the slanted edge, the acquisition and processing of the edge spread function (ESF), and the acquisition and processing of the line spread function (LSF). A combination of the Canny operator and Hough transform is proposed for the detection of the slanted edge, which improves the fitting accuracy and anti-interference ability of the algorithm. Further, the Canny operator is improved by constructing an adaptive filter function and introducing the Otsu method, which can more effectively smooth the image and remove its false edges. A method of processing ESF data by combining cubic spline interpolation and Savitzky–Golay (SG) filtering is proposed, which reduces the effects of noise and the non-uniform sampling of ESF on MTF. A method of LSF processing using Gaussian function fitting is proposed to further reduce the effect of noise on MTF. The improved algorithm is verified by the MTF measurement test applied to a specific type of Bayer filter color space camera. The simulation and test results show that the improved slanted-edge method discussed in this paper has greater precision and a better anti-interference ability, and it can effectively solve the difficult problem associated with MTF detection in Bayer filter color space cameras.

Structural vibration has always been a major concern in the engineering field. A dynamic vibration absorber in the form of contacts with adjustable stiffness (CDVA) offers effective vibration suppression and can improve conventional dynamic vibration absorbers with high sensitivity to frequency deviation and difficulty in adjusting the frequency. In this research, first, based on the theoretical model of the contact between a rubber ball and an inner cone, the feasibility of changing the axial contact state to change the structure’s natural frequency was verified using an ANSYS simulation. A theoretical model of the static contact stiffness between the ball and the inner cone was constructed using Hertzian contact theory and Hooke’s law, and a theoretical model of the cubic nonlinear elastic restoring force was used to characterize the stiffness properties of the rubber ball during compressive rebound. The steady-state frequency response equations of the main vibration structure were derived using the averaging method in conjunction with the two-degree-of-freedom dynamics model, and the stability of the solutions to the frequency response equations was obtained in conjunction with the stability determination criterion. Then, the impact of the CDVA’s design parameters on the nonlinear dynamic response of the primary vibration structure was simulated and analyzed. The resulting findings can serve as guidance for designing dynamic vibration absorber parameters. Based on the principles of ball-inner cone contact, a dynamic vibration absorber structure was proposed. A design test was conducted to verify the correctness of the contact stiffness model, and an experimental study was carried out to investigate the law of change in the dynamic stiffness and damping of the principle structure of CDVA under dynamic excitation conditions. Finally, the vibration test platform of the solidly supported beam structure was constructed, and vibration suppression tests of the CDVA in different compression states were conducted to investigate the tunability and feasibility of CDVA vibration suppression. The results showed that the dynamic vibration absorber had good vibration absorption characteristics and could be used for single-mode vibration suppression of multimodal main structures.

Aiming at the phenomenon of fiber print-through (FPT) during the curing process of carbon fiber-reinforced polymer (CFRP) mirrors, this paper effectively mitigates FPT by improving the replication technique. This paper simulates and analyzes the causes of FPT generation and then improves the replication technique based on multiple explorations of the replication process. In the improved replication technique, a mold is designed to assist in the curing process of the mirrors and to further suppress the FPT on the surface by applying pressure during the curing process. In addition, the layup method, resin matrix, and curing equipment are also optimized and improved. The surface roughness of the CFRP mirrors before and after the process improvement is measured using an optical surface profilometer, and the roughness parameters such as the arithmetic average deviation, root mean square error, and maximum height are obtained. Measurement results show that the improved replication technique effectively mitigates FPT, the surface of the obtained CFRP mirror is smoother, and the application of pressure during curing can further reduce the roughness of the mirror surface.

Aiming at the difficulty of detecting the modulation transfer function (MTF) of Bayer color cameras during focusing, the traditional scheme is modified in this paper. First, through analysis, it is found that the MTF of the Bayer detector decreased substantially compared to the monochromatic detector, which was caused by the loss of a large amount of light from the Bayer detector. When the MTF is calculated for the color image after de-mosaicing, the degradation of image quality leads to the inability to obtain the full-frequency MTF curve. Therefore, this paper proposes a solution to detect the MTFs of the three primary colors in the Bayer image individually, and then weight the MTFs of each primary color to obtain the MTF of the color image based on the calibration results of the light source. Then, considering the steps of differentiation and Fourier transform in the slanted-edge method, this paper solves the problem of non-uniform sampling of edge spread function by using the modification of the slanted-edge method with non-uniform Fourier transform. Finally, the optimal imaging position of a certain type of Bayer color camera is determined using the methods proposed in this paper. Simulation and test results verify the effectiveness and accuracy of the methods in this paper.