We report a facile and green route to reduce graphite oxide using urea as the reducing agent. UV-Vis, XRD and XPS results revealed that urea was an effective reducing agent in removing oxygen-containing groups from graphite oxide for restoring the conjugated electronic structure of graphene. The obtained reduced graphene oxide was tested as supercapacitor electrode. Gravimetric capacitances of 255 and 100 F g−1 at current densities of 0.5 and 30 A g−1, respectively, were observed. The reduced graphene oxide paper showed a volumetric capacitance of 196 F cm−3. After 1200 continuous cycles of galvanostatic charge–discharge, the electrode retained 93% of its capacitance. The electrocapacitive performance of the urea-reduced graphene oxide outperformed most of the previously reported graphene-based electrode materials, which were reduced by hydrazine or NaBH4. The present reduction method holds great promise for mass production of soluble graphene-based materials for electrochemical energy storage.
Caterpillar-like nanoflaky MnO2/carbon nanotube (CNT) nanocomposites are synthesized via a facile solution method. To build a three-dimensional hierarchy architecture, highly porous interconnected MnO2 nanoflakes are uniformly coated on the surface of the CNTs. As a promising anode material for lithium-ion batteries, the nanoflaky MnO2/CNT nanocomposite electrode exhibits a large reversible capacity of 801 mA h g−1 (∼1000 mA h g−1 can be attributed to the MnO2 porous layer alone) for the first cycle without capacity fade for the first 20 cycles and with a good rate capability. The superior electrochemical performance of the MnO2/CNT nanocomposite electrode compared to the pure MnO2 electrode can be attributed to its unique hierarchy architecture, which is able to provide fast lithium ion and electron transport and to accommodate a large volume change during the conversion reactions.
Portable electronic devices and electric vehicles have become indispensable in daily life and caused an increasing demand for high‐performance lithium‐ion batteries (LIBs) with high‐energy‐density. This work compares the intrinsic characteristics and Li+ conduction mechanisms of various electrolytes, aiming at emphasizing their suitability for high‐energy‐density LIBs. Among all electrolytes, polymer‐based solid‐state electrolytes (SSEs) are the most promising candidates, as they demonstrate the most comprehensive properties. The advantages and disadvantages of commonly used polymer matrix materials of SSEs are discussed, along with typical approaches to address their limitations. As significant issues for high‐energy‐density and cycle stability, the development related to the cathode/electrolyte interfacial contact and wetting, interfacial electrochemical compatibility, and interfacial Li+ conduction in LIBs employing polymer‐based SSEs, as well as the anode/electrolyte interfacial chemical stability and lithium dendrite suppression are comprehensively reviewed and analyzed. Finally, perspectives on future research directions for developing high‐energy‐density LIBs are highlighted building upon the existing literature.
MnO2/carbon nanotube [CNT] nanocomposites with a CNT core/porous MnO2 sheath hierarchy architecture are synthesized by a simple hydrothermal treatment. X-ray diffraction and Raman spectroscopy analyses reveal that birnessite-type MnO2 is produced through the hydrothermal synthesis. Morphological characterization reveals that three-dimensional hierarchy architecture is built with a highly porous layer consisting of interconnected MnO2 nanoflakes uniformly coated on the CNT surface. The nanocomposite with a composition of 72 wt.% (K0.2MnO2·0.33 H2O)/28 wt.% CNT has a large specific surface area of 237.8 m2/g. Electrochemical properties of the CNT, the pure MnO2, and the MnO2/CNT nanocomposite electrodes are investigated by cyclic voltammetry and electrochemical impedance spectroscopy measurements. The MnO2/CNT nanocomposite electrode exhibits much larger specific capacitance compared with both the CNT electrode and the pure MnO2 electrode and significantly improves rate capability compared to the pure MnO2 electrode. The superior supercapacitive performance of the MnO2/CNT nancomposite electrode is due to its high specific surface area and unique hierarchy architecture which facilitate fast electron and ion transport.
Rechargeable lithium ion batteries have ruled the consumer electronics market for the past 20 years and have great significance in the growing number of electric vehicles and stationary energy storage applications. However, in addition to concerns about electrochemical performance, the limited availability of lithium is gradually becoming an important issue for further continued use and development of lithium ion batteries. Therefore, a significant shift in attention has been taking place towards new types of rechargeable batteries such as sodium-based systems that have low cost. Another important aspect of sodium battery is its potential compatibility with the all-solid-state design where solid electrolyte is used to replace liquid one, leading to simple battery design, long life span, and excellent safety. The key to the success of all-solid-state battery design is the challenge of finding solid electrolytes possessing acceptable high ionic conductivities at room temperature. Herein, we report a novel sodium superionic conductor with NASICON structure, Na3.1Zr1.95Mg0.05Si2PO12 that shows high room-temperature ionic conductivity of 3.5 × 10−3 S cm−1. We also report successful fabrication of a room-temperature solid-state Na-S cell using this conductor.
Modified Li-rich layered cathode Li(Li0.2Mn0.54Ni0.13Co0.13)O2 has been synthesized by a simple strategy of using surface treatment with various amounts (0–30 wt.%) of Super P (carbon black). Based on detailed characterizations from X-ray diffraction (XRD), high resolution transmission electron microscope (HRTEM), X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS), it is suggested that the phase transformation from Li2MnO3-type of structure to spinel-like phase take place at the surface regions of particles during post annealing process at 350°C, leading to increase in both first coulombic efficiency and rate capability, from 78% and 100 mAh·g−1 (charge capacity at 2500 mA·g−1) of the pristine material to 93.4% and 200 mAh·g−1. The evidences of spinel formation and the reasons for electrochemical enhancement are systematically investigated.