This article presents the results of burn rate measurements conducted for a Fe/BaO2 pyrotechnic delay composition. Compositions with an iron content between 15% (w/w) and 50% (w/w) yielded burn rates in the range of 4–36 mm s−1. Mixtures containing more than 50% (w/w) iron could not be initiated by a powder fuse and are not suited for application as delay compositions. This study also presents a cost-efficient method for measuring linear combustion velocities and its application to the investigation of the Fe/BaO2 composition. Thermogravimetric and XRD studies have revealed that the reactions between iron and barium peroxide take place in the solid phase, leading to the formation of varied spinels.
The widespread use of pyrotechnic compositions in time delay detonators is the reason for research aimed at expanding knowledge of the combustion properties of new pyrotechnic mixtures, whose components react with each other in the solid or liquid state. Such a method of combustion would make the rate of combustion independent of the pressure inside the detonator. This paper presents the effect of the parameters of W/CuO mixtures on their properties of combustion. As this composition has not been the subject of previous research and is not described in the literature, the basic parameters, such as the burning rate and the heat of combustion, were determined. In order to determine the reaction mechanism, a thermal analysis was performed, and the combustion products were determined using the XRD technique. Depending on the quantitative composition and density of the mixture, the burning rates were between 4.1–6.0 mm/s and the heat of combustion in the range of 475–835 J/g was measured. The gas-free combustion mode of the chosen mixture was proved using DTA and XRD. Determination of the qualitative composition of the combustion products and the heat of combustion allowed estimation of the adiabatic combustion temperature.
This study investigates the combustion characteristics of silicon-based time-delay compositions with bismuth(III) oxide (Bi2O3), antimony(III) oxide (Sb2O3), and lead(II,IV) oxide (Pb3O4) to identify formulations with pressure-independent burn rates. Unlike conventional pyrotechnic compositions, silicon-based mixtures offer an improved energy density and reduced sensitivity to pressure variations. The linear combustion rate of the compositions was determined for a wide range of silicon contents and for different compaction pressures. Experimental results show that burn rates range from 8 mm s⁻1 to 195 mm s⁻1, depending on the metal oxide type and silicon content. The highest rate (195 mm s⁻1) was observed for Si/Pb3O4 at 30 wt.% silicon, while Si/Sb2O3 had the lowest (10 ÷ 35 mm s⁻1). The calorimetric heat of combustion varied between 1200 J g⁻1 and 1400 J g⁻1, with adiabatic combustion temperatures reaching 2200 K, calculated from this heat. DTA and XRD confirmed the condensed-phase combustion, forming reduced metal phases and silicon oxides. SEM and EDS revealed a porous residue structure. This work introduces a novel approach to time-delay compositions using silicon as a primary fuel. It shows that specific silicon oxide–metal systems maintain stable combustion for different loading pressures and advance pyrotechnic formulations for safer and more efficient industrial and defense applications.
25 November 2020 in Materiały Wysokoenergetyczne / High Energy Materials
The fallowing article presents the combustion studies of Fe/alkaline earth metals peroxides composition. It contains a literature review and the results of own research, which aim is to determine the possibility of using iron-based thermite compositions in time delay elements. The article focuses on the investigation of combustion front propagation rate as a function of a pressing load, the iron content and the purity of used oxidants. The DSC, TG and XRD analysis confirmed that reactions in this system occurs mainly in the solid state.
Antimony and potassium manganate(VII) compositions are widely used in time delay elements of detonators. Despite the existing literature on such systems, there is no complete information on the burning process of Sb/KMnO4 compositions in closed systems. There are also no data on the heat of their combustion in conditions of increased pressure without the access of oxygen from the air and on the composition of solid combustion products. These issues are the subject of the presented work.
27 March 2019 in Central European Journal of Energetic Materials