Bacterial nanocellulose (BNC) is a natural biomaterial with a wide range of biomedical applications. BNC contains 99 % of water which makes it too thick to be used as a bioimplant material. The aim of the work was to determine the effect of the BNC dehydration followed by rehydration on its mechanical and physicochemical properties, in the context of the use of BNC as bio-prostheses in the cardiovascular system. Dehydration involved the convection-drying at 25 and 105 °C, and the freeze-drying, while rehydration - the soaking in water. All modified BNC samples had reduced thickness, and results obtained from FT-IR, XRD, and SEM analysis revealed that 25 °C BNC convection-dried after soaking in water was characterized by the highest: tensile strength (17.4 MPa), thermal stability (253 °C), dry mass content (4.34 %) and Iα/Iβ ratio (1.10). Therefore, 25 °C convection-dried BNC followed by soaking in water can be considered as a material suitable for cardiovascular implants.
1 April 2019 in Materials Science and Engineering: C
The paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate an unfavorable stress distribution. The increase in the surface hardness was obtained due to the work hardening effect. Microstructure, phase composition, and chemical composition of the grinded surface layer were examined using an X-ray diffractometer, light microscope, and scanning microscope equipped with X-ray energy-dispersive spectroscopy, respectively. Hardness on the grinded surface and on the cross-section was also determined. It was shown that the grinding of C45 steel causes work hardening of its surface layer without phase transformation. What is more, only grinding to a depth of 20 μm caused the formation of an oxide scale on the work-hardened surface layer. Nanoindentation test on the cross-section, at a short distance from the grinded surface, has shown that ferrite grains were more susceptible to work hardening than pearlite grains due to the creation of an equiaxed cellular microstructure, and that different dislocation substructure was created in the work-hardened surface layer after grinding to different depths.
6 May 2024 in International Journal of Biological Macromolecules
Bacterial nanocellulose (BNC) is a promising material for heart valve prostheses. However, its low strength properties limit its applicability in cardiovascular surgery. To overcome these limitations, the mechanical properties of BNC can be improved through modifications. The aim of the research was to investigate the extent to which the mechanical properties of BNC can be altered by modifying its structure during its production and after synthesis. The study presents the results of various analyses, including tensile tests, nanoindentation tests, X-ray diffraction (XRD) tests, scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR) and Raman spectroscopy, conducted on BNC chemically modified in situ with hyaluronic acid (BNC/HA) and physically modified ex situ through a dehydration/rehydration process (BNC 25DR, BNC105DR, BNC FDR and BNC/HA 25DR, BNC/HA 105DR, BNC/HA FDR). The results demonstrate that both chemical and physical modifications can effectively shape the mechanical properties of BNC. These modifications induce changes in the crystalline structure, pore size and distribution, and residual stresses of BNC. Results show the effect of the crystalline structure of BNC on its mechanical properties. There is correlation between hardness and Young's modulus and Iα/Iβ index for BNC/HA and between creep rate of BNC/HA, and Young's modulus for BNC vs Iα/Iβ index.
This study investigates the impact of build orientation on the corrosion resistance of CoCrWMo alloys fabricated by Laser Powder Bed Fusion (L-PBF). Samples printed at angles from 0° to 90° were characterized using SEM, XRD (with modified Williamson-Hall and Warren-Averbach analysis), and potentiodynamic polarization in Ringer’s solution. The results revealed that build orientation strongly affects microstrain, dislocation density, and dislocation character, which in turn govern passive layer composition and corrosion behavior. The sample printed at 90° exhibited the highest corrosion resistance, correlating with the lowest dislocation density, minimal microstrain, and the highest fraction of screw dislocations. XPS analysis showed this sample had the most Cr-rich passive layer, with Cr₂O₃ accounting for over 60% of oxide species. In contrast, low-angle samples exhibited more edge dislocations, higher microstrain, and less protective oxide films. These findings highlight the critical role of build-induced crystallographic anisotropy and defect structure in shaping corrosion response in L-PBF-processed biomedical alloys. The study also demonstrates the utility of advanced XRD-based methods for quantifying lattice distortions and dislocation populations. Importantly, the results support sustainable design strategies by enhancing corrosion resistance through process control, reducing reliance on coatings or alloying, and promoting resource-efficient manufacturing of biomedical and engineering components.
This study investigates the strain hardening and dislocation structure in the surface layers of C45 steel subjected to precision grinding at various depths. The aim was to assess how different grinding conditions influence the mechanical response and defect structure of ferrite. Nanoindentation was used to evaluate mechanical properties, while X-ray diffraction analysis provided data on the microstrain, crystallite size, and residual stress. The character and density of dislocations were further examined using modified Williamson–Hall and q-parameter analysis. The results revealed that the sample ground to a depth of 2 μm exhibited the highest density of statistically stored dislocations, as well as the lowest dislocation mobility. This condition also corresponded to the highest residual stresses and the greatest share of screw dislocations, indicating intense strain localization. In contrast, deeper grinding depths resulted in lower dislocation densities and reduced the strain energy. The observed trends highlight the formation of a dislocation-rich nanostructured layer in the shallowest ground region. These findings provide new insights into the mechanisms of surface hardening in ferritic steels and demonstrate how the depth of material removal during grinding governs the subsurface microstructure and strengthening effects.