Juan C. Diez

Dr. Juan C. Diez

orcid

Research Focus & Metrics

Academic Career Length

28Years (1999-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2019 in Journal of the European Ceramic Society
Verified
Journal Article
Open access
MTMiguel A. Torres
Miguel A. Torres
FCF.M. Costa
F.M. Costa
DFD. Flahaut
D. Flahaut
KTKarim TOUATI
Karim TOUATI
SRSh. Rasekh
Sh. Rasekh
Andres SoteloAndres Sotelo
Andres Sotelo

1 July 2018 in Optics and Lasers in Engineering
Verified
Journal Article
Open access
MVM. Villar
M. Villar
Christian GarnierChristian Garnier
Christian Garnier
FCFrance CHABERT
France CHABERT
VNValérie Nassiet
Valérie Nassiet
DSD. Samélor
D. Samélor
MMM.A. Madre
M.A. Madre

1 October 2014 in Journal of the European Ceramic Society
Verified
Journal Article
Open access
Andres SoteloAndres Sotelo
Andres Sotelo
SRSh. Rasekh
Sh. Rasekh
Gabriel ConstantinescuGabriel Constantinescu
Gabriel Constantinescu
HAH. Amaveda
H. Amaveda
MTMiguel A. Torres
Miguel A. Torres
JDJuan C. Diez
Juan C. Diez
Bi2-xPbxSr2CaCu2Oy textured materials (x=0.0, 0.2, 0.4, and 0.6) have been successfully prepared by the laser floating zone technique. Microstructure and electrical properties (JC and TC) have been clearly affected by Pb addition. From the E-I curves, slope of the transition between the superconducting and the normal state (n) at 77K reaches a maximum of about 16 for the 0.4 Pb doped samples. This value is much higher than the typical ones for the Bi-2212 materials. Moreover, when the electrical properties of the 0.4 Pb doped samples are measured at lower temperatures (between 65 and 77K), n values increase when the temperature is decreased. A maximum n value of 32 has been reached at 65K which makes this material very attractive for its use as resistive fault current limiters. © 2014 Elsevier Ltd.The authors wish to thank the Gobierno de Aragón (Research Groups T12 and T87) for financial support. M. A. Madre and H. Amaveda acknowledge the Spanish MINECO-FEDER (Project MAT2011-22719) for funding. The technical contributions of C. Estepa and C. Gallego are also acknowledged. Sh. Rasekh acknowledges a JAE-PreDoc2010 grant from CSIC.Peer Reviewe

22 December 2012 in Journal of Superconductivity and Novel Magnetism
Verified
Journal Article
Open access
PDF file
FCF. M. Costa
F. M. Costa
SRShahed Rasekh
Shahed Rasekh
Nuno FerreiraNuno Ferreira
Nuno Ferreira
Andres SoteloAndres Sotelo
Andres Sotelo
JDJuan C. Diez
Juan C. Diez
MMM. A. Madre
M. A. Madre
Bi-2212/Ag superconducting ceramics were grown using the electrically assisted laser floating zone (EALFZ) technique. The main goal was improving the superconducting properties by applying an electrical current through the sample during the solidification process. The effect of a 100 mA current intensities in two configurations were studied: (i) direct current (connecting the seed rod to the positive pole and the feed to the negative one) and (ii) reverse current (positive pole connected to the feed rod and negative to the seed one). The resulting textured cylindrical bars were annealed in order to obtain the superconducting phases. A strong correlation between current polarity, grain alignment and superconducting properties was observed. The rods grown under direct current exhibit higher critical current density (∼3000 A/cm2) than the ones grown under conventional method (∼2300 A/cm2) or under reverse current condition (∼35 A/cm2). The superior value obtained for the direct current results from a better grain alignment and fewer amount of second phases.

16 August 2006 in Physica Status Solidi (a)
Verified
Journal Article
Closed access
PDF file
LALuis A. Angurel
Luis A. Angurel
JDJuan C. Diez
Juan C. Diez
GFGermán Francisco De La Fuente
Germán Francisco De La Fuente
FGF. Gimeno
F. Gimeno
FLF. Lera
F. Lera
MAM. P. Arroyo
M. P. Arroyo

14 June 2017 in Advances in Applied Ceramics: Structural, Functional and Bioceramics
Verified
Journal Article
Closed access
ASA. Sotelo
A. Sotelo
SRSh. Rasekh
Sh. Rasekh
MTMiguel A. Torres
Miguel A. Torres
MMM. A. Madre
M. A. Madre
JDJuan C. Diez
Juan C. Diez
Bi2Sr2Co1.8Ox thermoelectric (TE) materials were prepared by three different synthesis methods producing nanosized precursors: coprecipitation (with ammonium carbonate or oxalic acid) and attrition milling, which were compared with those obtained by the classical solid state method. Microstructure has shown that precursors produced by coprecipitation and attrition milling methods produced nanometric precursors much smaller than the typical sizes produced by the solid state route. The TE properties are in agreement with the microstructural features, leading to lower resistivity in all the samples, compared with the solid state ones, while Seebeck coefficient is practically unchanged in all cases. As a consequence, maximum power factor values of around four times higher than those obtained in the classical solid state method have been determined. Moreover, the highest power factor value at 650°C is higher than the best results obtained in as-grown textured materials produced by the laser floating zone technique.