Superhydrophobic antibacterial fabric possesses properties of antibacterial and antibacterial adhesion and shows huge demand in the field of medical textiles. However, current technologies are unable to fully address this. Hence, a simple method is highly desirable. Herein, the pristine polyester (PET) fabric is immersed into the solution containing ZnO nanoparticle and polydimethylsiloxane (PDMS), and the fiber surfaces are uniformly covered by a ZnO-PDMS layer after being treated by low pressure Ar plasma. The weight gain rate of the treated fabric is 3.5%, which is basically unchanged, and the air permeability, moisture permeability, and tensile properties of the fabric are basically not affected. It is found that the water contact angle (WCA) of the fabric is over 162.7°and sliding angle (SA) is less than 10°. The stable binding of PDMS and PET fibers induces a robust superhydrophobicity; even after 300 washing cycles and 600 friction cycles, it still remains superhydrophobic. The antibacterial rates of Escherichia coli and Staphylococcus aureus before washing were 99.89% and 99.85%, respectively, and after 100 cycles of washing, the antibacterial rates decreased to 99.36% and 99.17%, respectively. Therefore, it shows a good development prospect in the application of protecting clothing or textiles that require good antibacterial properties (such as bed sheets, duvet covers, etc.).
The existing coating systems used for the preparation of super-hydrophobic surfaces are facing new challenges because the use of organic solvents and long-carbon-chain organic fluorine monomers is banned. In this article, the authors have proven that by using inductively coupled plasma-enhanced chemical vapor deposition (PECVD) with argon (Ar), which is a completely dry process, lauryl methacrylate (LMA) can produce a stable super-hydrophobic coating effect. The effect of electron temperature on the super-hydrophobicity of cotton fabrics is investigated in terms of water repellency, chemical composition, and surface morphology. It is found that the improvement in the hydrophobicity of cotton fabric is attributed to the deposition of alkyl and ester groups, and the formation of a micro–nano-structure on the surface of the fabric after plasma treatment. The electron temperature plays an important role in achieving the super-hydrophobicity of cotton fabrics. The plasma-enhanced coating may offer a safe and dry super-hydrophobic technique with diverse applications.
Defective functional-group-endowed polymer semiconductors, which have unique photoelectric properties and rapid carrier separation properties, are an emerging type of high-performance photocatalyst for various energy and environmental applications. However, traditional oxidation etching chemical methods struggle to introduce defects or produce special functional group structures gently and controllably, which limits the implementation and application of the defective functional group modification strategy. Here, with the surface carboxyl modification of graphitic carbon nitride (g-C3N4) photocatalyst as an example, we show for the first time the feasibility and precise modification potential of the non-thermal plasma method. In this method, the microwave plasma technique is employed to generate highly active plasma in a combined H2+CO2 gas environment. The plasma treatment allows for scalable production of high-quality defective carboxyl group-endowed g-C3N4 nanosheets with mesopores. The rapid H2+CO2 plasma immersion treatment can precisely tune the electronic and band structures of g-C3N4 nanosheets within 10 min. This conjoint approach also promotes charge-carrier separation and accelerates the photocatalyst-catalyzed H2 evolution rate from 1.68 mmol h−1g−1 (raw g-C3N4) to 8.53 mmol h−1g−1 (H2+CO2-pCN) under Xenon lamp irradiation. The apparent quantum yield (AQY) of the H2+CO2-pCN with the presence of 5 wt.% Pt cocatalyst is 4.14% at 450 nm. Combined with density functional theory calculations, we illustrate that the synergistic N vacancy generation and carboxyl species grafting modifies raw g-C3N4 materials by introducing ideal defective carboxyl groups into the framework of heptazine ring g-C3N4, leading to significantly optimized electronic structure and active sites for efficient photocatalytic H2 evolution. The 5.08-times enhancement in the photocatalytic H2 evolution over the as-developed catalysts reveal the potential and maneuverability of the non-thermal plasma method in positioning carboxyl defects and mesoporous morphology. This work presents new understanding about the defect engineering mechanism in g-C3N4 semiconductors, and thus paves the way for rational design of effective polymeric photocatalysts through advanced defective functional group engineering techniques evolving CO2 as the industrial carrier gas.
Potassium iodate (KIO3), an edible salt additive, was used as a critical waste-free modifier in the thermal polymerization of g-C3N4, leading to the harmonious K–I–O co-modification of g-C3N4 for a boosted charge separation and photocatalytic performance.
Transition-metal monometallic photocatalysts have received extensive attention owing to the maximization of atomic utilization efficiency. However, in previous related works, single-atom loading and stability are generally low due to limited anchor sites and mechanisms. Recently, adding transition-metal monatomic sites to defective carbon nitrides has a good prospect, but there is still lack of diversity in defect structures and preparation techniques. Here, a strategy for preparing defect-type carbon-nitride–coupled monatomic copper catalysts by an ultrafast plasma method is reported. In this method, oxalic acid and commercial copper salt are used as a carboxyl defect additive and a copper source, respectively. Carbon nitride samples containing carboxyl defects and monatomic copper can be processed within 10 min by one-step argon plasma treatment. Infrared spectroscopy and nuclear magnetic resonance prove the existence of carboxyl defects. Spherical aberration electron microscopy and synchrotron radiation analysis confirm the existence of monatomic copper. The proportion of monatomic copper is relatively high, and the purity is high and very uniform. The Cu PCN as-prepared shows not only high photo-Fenton pollutant degradation ability but also high photocatalytic hydrogen evolution ability under visible light. In the photocatalytic reaction, the reversible change of Cu+/Cu2+ greatly promotes the separation and transmission of photogenerated carriers and improves the utilization of photoelectrons. The photocatalytic hydrogen evolution rate of the optimized sample is 8.34 mmol g−1·h−1, which is 4.54 times that of the raw carbon nitride photocatalyst. The cyclic photo-Fenton experiment confirms the catalyst has excellent repeatability in a strong oxidation environment. The synergistic mechanism of the photocatalyst obtained by this plasma is the coordination of single-atom copper sites and carboxyl defect sites. The single copper atoms incorporated can act as an electron-rich active center, enhancing the h+ adsorption and reduction capacity of Cu PCN. At the same time, the carboxyl defect sites can form hydrogen bonds to stabilize the production of hydrogen atoms and subsequently convert them to hydrogen because of the unstable hydrogen bond structure. This plasma strategy is green, convenient, environment-friendly, and waste-free. More importantly, it has the potential for large-scale production, which brings a new way for the general preparation of high-quality monatomic catalysts.